I.S. EN ISO 16228:2018
Current
The latest, up-to-date edition.
FASTENERS - TYPES OF INSPECTION DOCUMENTS (ISO 16228:2017)
Hardcopy , PDF
English
01-01-2018
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Inspection
5 Requirements for fastener inspection
documents
6 Required content for each type of fastener
inspection document
7 Amendment to inspection documents
8 Transmission of inspection documents
Annex A (informative) - Examples of inspection
documents
Annex B (informative) - Code numbers applicable
to fasteners
Bibliography
Defines the different types of fastener inspection documents issued by the fastener manufacturer or distributor and/or by the external authorized representative on specific request of the purchaser at the time of the order.
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN ISO 16228:2018 | Identical |
| ISO 16228:2017 | Identical |
| ISO 16047:2005 | Fasteners — Torque/clamp force testing |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ISO 10683:2014 | Fasteners Non-electrolytically applied zinc flake coatings |
| ISO 10684:2004 | Fasteners — Hot dip galvanized coatings |
| ISO 4042:1999 | Fasteners Electroplated coatings |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ISO 6157-3:1988 | Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements |
| ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
| ISO 6157-1:1988 | Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements |
| ISO 14589:2000 | Blind rivets Mechanical testing |
| ISO 2320:2015 | Fasteners Prevailing torque steel nuts Functional properties |
| ISO 16426:2002 | Fasteners — Quality assurance system |
| ISO 10666:1999 | Drilling screws with tapping screw thread — Mechanical and functional properties |
| EN 10168:2004 | Steel products - Inspection documents - List of information and description |
| ISO 225:2010 | Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions |
| ISO 4032:2012 | Hexagon regular nuts (style 1) — Product grades A and B |
| ISO 15330:1999 | Fasteners — Preloading test for the detection of hydrogen embrittlement — Parallel bearing surface method |
| ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners with specified hardness classes Coarse thread and fine pitch thread |
| ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress |
| ISO 15977:2002 | Open end blind rivets with break pull mandrel and protruding head — AIA/St |
| ISO 3506-4:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 4: Tapping screws |
| ISO 7089:2000 | Plain washers Normal series Product grade A |
| ISO 3800:1993 | Threaded fasteners — Axial load fatigue testing — Test methods and evaluation of results |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 6157-2:1995 | Fasteners Surface discontinuities Part 2: Nuts |
| ISO/TR 6306:1989 | Chemical analysis of steel Order of listing elements |
| ISO 2702:2011 | Heat-treated steel tapping screws — Mechanical properties |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| ISO 3269:2000 | Fasteners Acceptance inspection |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| ISO 4014:2011 | Hexagon head bolts Product grades A and B |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.