• Shopping Cart
    There are no items in your cart

I.S. EN ISO 16911-1:2013

Current

Current

The latest, up-to-date edition.

STATIONARY SOURCE EMISSIONS - MANUAL AND AUTOMATIC DETERMINATION OF VELOCITY AND VOLUME FLOW RATE IN DUCTS - PART 1: MANUAL REFERENCE METHOD (ISO 16911-1:2013)

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

01-01-2013

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.


Dates of withdrawal of national standards are available from NSAI.

€124.00
Excluding VAT

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principle
6 Selection of monitoring approach
7 Measuring equipment
8 Performance characteristics and requirements
9 Measurement procedure
10 Calculation of results
11 Establishment of the uncertainty of results
12 Evaluation of the method
Annex A (normative) - Measurement of velocity
        using differential pressure based techniques
Annex B (normative) - Vane anemometer
Annex C (normative) - Tracer gas dilution method
        determination of volume flow rate and
        average velocity
Annex D (normative) - Transit time tracer gas
        method determination of average velocity
Annex E (normative) - Calculation of flue gas
        volume flow rate from energy consumption
Annex F (informative) - Example of uncertainty
        budget established for velocity and volume
        flow rate measurements by Pitot tube
Annex G (informative) - Description of validation
        studies
Annex H (informative) - Differential pressure
        measurement
Annex I (informative) - The use of time of flight
        measurement instruments based on modulated
        laser light
Annex J (informative) - Relationship between this
        International Standard and the essential
        requirements of EU Directives
Bibliography

Defines a method for periodic determination of the axial velocity and volume flow rate of gas within emissions ducts and stacks.

DocumentType
Standard
Pages
99
PublisherName
National Standards Authority of Ireland
Status
Current

Standards Relationship
ISO 16911-1:2013 Identical
EN ISO 16911-1:2013 Identical

EN 15267-3:2007 Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources
BS 5857-1.4:1980 Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of water flow Transit time method using non-radioactive tracers
BS 5857-2.4:1980 Methods for measurement of fluid flow in closed conduits, using tracers. Measurement of gas flow Transit time method using radioactive tracers
ISO 1928:2009 Solid mineral fuels Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value
CEN/TS 14793:2005 Stationary source emission - Intralaboratory validation procedure for an alternative method compared to a reference method
ISO 14956:2002 Air quality — Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty
ISO 1170:2013 Coal and coke Calculation of analyses to different bases
ECA 4-02 : 2013 EVALUATION OF THE UNCERTAINTY OF MEASUREMENT IN CALIBRATION
EN 14789:2017 Stationary source emissions - Determination of volume concentration of oxygen - Standard reference method: Paramagnetism
EN 15259:2007 Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report
EN 13284-1:2017 Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method
EN 14181:2014 Stationary source emissions - Quality assurance of automated measuring systems
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
EN 12952-15:2003 Water-tube boilers and auxiliary installations - Part 15: Acceptance tests
EN 14790:2017 Stationary source emissions - Determination of the water vapour in ducts - Standard reference method
ISO 20988:2007 Air quality Guidelines for estimating measurement uncertainty
ISO 10780:1994 Stationary source emissions — Measurement of velocity and volume flowrate of gas streams in ducts
ISO 3966:2008 Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.