I.S. EN ISO 20029-2:2018
Current
The latest, up-to-date edition.
PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES (ISO 20029-2:2017)
Hardcopy , PDF
English
01-01-2018
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of test specimens
5 Conditioning of test specimens
6 Determination of properties
Annex A (informative) - Determination of tensile properties
Bibliography
Defines the methods of preparation of test specimens and the standard test methods to be used in determining the properties of thermoplastic polyester/ester and polyether/ester elastomer moulding and extrusion materials.
| DevelopmentNote |
Supersedes I.S. EN ISO 14910-2. (03/2018)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN ISO 20029-2:2018 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 16365-2:2014 | Plastics — Thermoplastic polyurethanes for moulding and extrusion — Part 2: Preparation of test specimens and determination of properties |
| ISO 22007-3:2008 | Plastics — Determination of thermal conductivity and thermal diffusivity — Part 3: Temperature wave analysis method |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| ISO 22007-4:2017 | Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method |
| ISO 974:2000 | Plastics — Determination of the brittleness temperature by impact |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic — Determination of compression set — Part 1: At ambient or elevated temperatures |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 34-1:2015 | Rubber, vulcanized or thermoplastic — Determination of tear strength — Part 1: Trouser, angle and crescent test pieces |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11357-3:2011 | Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature and enthalpy of melting and crystallization |
| ISO 11357-4:2014 | Plastics — Differential scanning calorimetry (DSC) — Part 4: Determination of specific heat capacity |
| ISO 294-4:2001 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of moulding shrinkage |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 15512:2016 | Plastics — Determination of water content |
| ISO 62:2008 | Plastics — Determination of water absorption |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 22007-2:2015 | Plastics — Determination of thermal conductivity and thermal diffusivity — Part 2: Transient plane heat source (hot disc) method |
| ISO 1133-2:2011 | Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 2: Method for materials sensitive to time-temperature history and/or moisture |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 20753:2008 | Plastics — Test specimens |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.