I.S. EN ISO 20753:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - TEST SPECIMENS (ISO 20753:2008)
Hardcopy , PDF
10-01-2019
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of test specimens
5 Types of test specimen and their dimensions
6 Report on preparation of test specimens
Annex A (informative) - Recommended applications for
multipurpose test specimens or parts thereof
Annex B (normative) - Designation system for test specimens
Bibliography
Describes dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding as well as to test specimens prepared by machining from sheets or shaped articles.
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 20753:2008 | Identical |
| EN ISO 20753:2014 | Identical |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 4589-3:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test |
| ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
| ISO 22088-1:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 1: General guidance |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| ISO 294-5:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy |
| ISO 11403-3:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties |
| ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
| ISO 22088-2:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 2: Constant tensile load method |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 22088-5:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 5: Constant tensile deformation method |
| ISO 2039-1:2001 | Plastics Determination of hardness Part 1: Ball indentation method |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 2039-2:1987 | Plastics Determination of hardness Part 2: Rockwell hardness |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 22088-3:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 3: Bent strip method |
| ISO 294-2:1996 | Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars |
| ISO 899-2:2003 | Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| IEC 60426:2007 | Electrical insulating materials - Determination of electrolytic corrosion caused by insulating materials - Test methods |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 22088-4:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 4: Ball or pin impression method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 22088-6:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 6: Slow strain rate method |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| ASTM D 1822 : 2013 : REDLINE | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.