ISO 28278-1:2011
Current
The latest, up-to-date edition.
Glass in building — Glass products for structural sealant glazing — Part 1: Supported and unsupported monolithic and multiple glazing
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
21-11-2011
Important note : Users cannot be edited or removed once added to your Multi user PDF.
ISO 28278-1:2011 specifies requirements for the suitability of supported and unsupported glass products for use in the structural sealant glazing (SSG) technique. Regarding glass products, ISO 28278-1:2011 constitutes a supplement to the requirements specified in the corresponding international standards with regard to verifying suitability for use in SSG systems.
Only soda lime silicate glass is taken into consideration in ISO 28278-1:2011.
The glass products are installed and bonded into the support under controlled environmental conditions as described in ISO 28278-2.
Plastic glazing is excluded from the scope of ISO 28278-1:2011.
The structural weatherproofing and sealant and outer seal of IGU products, which are commonly used in structural glazing applications are those based on organo-siloxane,"silicone" polymers, and recommended for use by the sealant manufacturer. Where there is a risk of earthquakes, the sealant design may not be sufficient to resist the loads, and complementary arrangements may be necessary.
ISO 28278-1:2011 does not preclude the use of other sealant types where these can demonstrate suitability for service according to ISO 28278-1:2011 and when used following the recommendations of the sealant manufacturer.
| Committee |
ISO/TC 160
|
| DevelopmentNote |
Supersedes ISO/DIS 28278-1. (11/2011)
|
| DocumentType |
Standard
|
| Pages |
63
|
| ProductNote |
THIS STANDARD ALSO REFERS TO JIS R 3209,
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| EN 13022-1:2014 | Glass in building - Structural sealant glazing - Part 1: Glass products for structural sealant glazing systems for supported and unsupported monolithic and multiple glazing |
| EN 572-3:2012 | Glass in building - Basic soda lime silicate glass products - Part 3: Polished wired glass |
| ASTM C 1401 : 2014 : REDLINE | Standard Guide for Structural Sealant Glazing |
| ISO 7389:2002 | Building construction Jointing products Determination of elastic recovery of sealants |
| ASTM C 1265 : 2017 : REDLINE | Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| EN 15434:2006+A1:2010 | Glass in building - Product standard for structural and/or ultra-violet resistant sealant (for use with structural sealant glazing and/or insulating glass units with exposed seals) |
| EN 27389 : 1990 | BUILDING CONSTRUCTION - JOINTING PRODUCTS - DETERMINATION OF ELASTIC RECOVERY |
| ASTM E 1300 : 2016 : REDLINE | Standard Practice for Determining Load Resistance of Glass in Buildings |
| ISO 11600:2002 | Building construction Jointing products Classification and requirements for sealants |
| ISO 7390:2002 | Building construction Jointing products Determination of resistance to flow of sealants |
| ISO 9002:1994 | Quality systems — Model for quality assurance in production, installation and servicing |
| EN 572-2:2012 | Glass in building - Basic soda lime silicate glass products - Part 2: Float glass |
| ISO 16269-6:2014 | Statistical interpretation of data — Part 6: Determination of statistical tolerance intervals |
| ISO 10563:2017 | Buildings and civil engineering works — Sealants — Determination of change in mass and volume |
| ISO 28278-2:2010 | Glass in building — Glass products for structural sealant glazing — Part 2: Assembly rules |
| EN 572-4:2012 | Glass in building - Basic soda lime silicate glass products - Part 4: Drawn sheet glass |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 11358-2:2014 | Plastics Thermogravimetry (TG) of polymers Part 2: Determination of activation energy |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| EN 572-5:2012 | Glass in building - Basic soda lime silicate glass products - Part 5: Patterned glass |
| EN 28339 : 1990 | BUILDING CONSTRUCTION - JOINTING PRODUCTS - SEALANTS - DETERMINATION OF TENSILE PROPERTIES |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| ASTM C 1036 : 2016 : REDLINE | Standard Specification for Flat Glass |
| ASTM C 1376 : 2015 : REDLINE | Standard Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass |
| EN 13022-2:2014 | Glass in building - Structural sealant glazing - Part 2: Assembly rules |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| ISO 3231:1993 | Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide |
| EN 1096-2:2012 | Glass in building - Coated glass - Part 2: Requirements and test methods for class A, B and S coatings |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.