ISO 6162-2:2012
Withdrawn
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
Hydraulic fluid power Flange connections with split or one-piece flange clamps and metric or inch screws Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Withdrawn date
19-02-2019
Superseded by
Language(s)
French, English
Published date
14-12-2012
Important note : Users cannot be edited or removed once added to your Multi user PDF.
ISO 6162-2:2012 gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at a pressure of 42 MPa (420 bar ). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals.
ISO 6162-2:2012 also recognizes the need to accommodate metric screw fasteners (type 1) (for DN 13 to DN 76), as well as to provide a means to use existing inch screw fasteners (type 2) (for DN 13 to DN 51).
These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.
Surges of pressure higher than the nominal ratings will reduce the ability of the flange connections to retain the hydraulic fluid. This needs to be taken into account in the design of the hydraulic system.
| DocumentType |
Standard
|
| Pages |
21
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS ISO 6162-2:2012 | Identical |
| NF ISO 6162-2 : 2018 | Identical |
| DIN ISO 6162-2:2006-02 | Identical |
| SN ISO 6162-2 : 2005 | Identical |
| NEN ISO 6162-2 : 2012 | Identical |
| 16/30328245 DC : 0 | BS ISO 6164 - HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 10 TO 80 |
| SAE J2551/3_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications - Part 3: Procurement |
| BS ISO 6022:2006 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 25M Pa (250 bar) series |
| BS ISO 10946:1999 | Hydraulic fluid power. Gas-loaded accumulators with separator. Selection of preferred hydraulic ports |
| 06/30128831 DC : DRAFT MAR 2006 | ISO 6020-1 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES |
| UNE-EN ISO 4413:2011 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| ISO 17165-1:2007 | Hydraulic fluid power — Hose assemblies — Part 1: Dimensions and requirements |
| UNE-EN ISO 19879:2010 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
| EN ISO 19879:2010 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
| DIN ISO 6022:2008-06 | HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES |
| DIN EN ISO 16330:2004-08 | Reciprocating positive displacement pumps and pump units - Technical requirements (ISO 16330:2003) |
| 09/30202316 DC : 0 | BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES |
| BS ISO 6020-1:2007 | Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Medium series |
| SAE J846_201511 | Coding Systems for Identification of Fluid Conductors and Connectors |
| 07/30163202 DC : 0 | BS ISO 12151-3 - CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
| DIN EN ISO 4413:2011-04 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| SAE J515_201511 | Specification for O-Ring Materials Used with Hydraulic Connectors |
| ISO 6164:1994 | Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar) |
| SAE J2593_201502 | Information Report for the Installation of Fluid Conductors and Connectors |
| SAE J518/3_201511 | Hydraulic Flange Clamps, 2-Screw Flange Connection to be used with SAE J518-1 (Code 61) Connections where Only Low Pressure is Required |
| I.S. EN ISO 19879:2010 | METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
| PD ISO/TS 11672:2016 | Connectors for fluid power and general use. Designation and nomenclature |
| UNI ISO 12151-3 : 2012 | CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
| BS ISO 17165-1:2007 | Hydraulic fluid power. Hose assemblies Dimensions and requirements |
| ISO 6022:2006 | Hydraulic fluid power — Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series |
| BS ISO 12151-3:2010 | Connections for hydraulic fluid power and general use. Hose fittings Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| SAE J2551/2_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 2: General Specifications and Performance Requirements |
| SAE J2551/1_201302 | Recommended Practices for Fluid Conductor Carbon, Alloy and High Strength Low Alloy Steel Tubing Applications-Part 1: Design and Fabrication |
| PD ISO/TS 17165-2:2013 | Hydraulic fluid power. Hose assemblies Practices for hydraulic hose assemblies |
| SAE J1677_201612 | Tests and Procedures for Carbon Steel and High Strength Low Alloy Steel Tubing |
| SAE J518/2_201704 | Hydraulic Flanged Tube, Pipe, and Hose Connections, 4-Screw Flange Connection Part 2: 42 MPa (Code 62) |
| 03/110806 DC : DRAFT JUNE 2003 | BS ISO 19879 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
| SAE J2614_201801 | Welded and Cold-Drawn, High Strength (500 MPa Tensile Strength) Hydraulic Tubing, for Bending, Flaring, Cold Forming, Welding and Brazing |
| UNI ISO 17165-1 : 2012 | HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS |
| DIN ISO 6020-1:2010-07 | Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series - Part 1: Medium series (ISO 6020-1:2007) |
| SAE J518/1_201301 | Hydraulic Flanged Tube, Pipe, and Hose Connections, 4-Screw Flange Connection Part 1: 3.5 MPa to 35 MPa (Code 61) |
| ISO 6020-1:2007 | Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 1: Medium series |
| BS EN ISO 16330:2003 | Reciprocating positive displacement pumps and pump units. Technical requirements |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| ISO 16330:2003 | Reciprocating positive displacement pumps and pump units Technical requirements |
| ISO 19879:2010 | Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections |
| EN ISO 16330:2003 | Reciprocating positive displacement pumps and pump units - Technical requirements (ISO 16330:2003) |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| SAE J1065_201605 | Nominal Reference Working Pressures for Steel Hydraulic Tubing |
| ISO 12151-3:2010 | Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends |
| SAE J2551_201309 | Recommended Practices for Fluid Conductor Carbon and Alloy Steel Tubing Applications |
| BS EN ISO 4413:2010 | Hydraulic fluid power. General rules and safety requirements for systems and their components |
| UNI EN ISO 19879 : 2011 | METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS |
| NF EN ISO 4413 : 2011 | HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS |
| NF ISO 12151-3 : 2010 | CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS |
| DIN EN ISO 19879:2011-01 | Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010) |
| BS EN ISO 19879:2010 | Metallic tube connections for fluid power and general use. Test methods for hydraulic fluid power connections |
| DIN ISO 12151-3:2012-08 | Connections for hydraulic fluid power and general use - Hose fittings - Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends (ISO 12151-3:2010) |
| NFPA T2.24.2 : 2007 | HYDRAULIC FLUID POWER SYSTEMS - METHODS FOR PREVENTING EXTERNAL LEAKAGE |
| NFPA T2.24.2 : 2007 : R2012 | HYDRAULIC FLUID POWER SYSTEMS - METHODS FOR PREVENTING EXTERNAL LEAKAGE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.