NEMA ICS 61800-1:2002(R2007)

Foreword
1 GENERAL
  1.1 Scope and Object
  1.2 Normative References
  1.3 Symbols
2 DEFINITIONS
  2.1 System
      2.1.1 d.c. Power Drive System (PDS)
      2.1.2 d.c. Power Drive System-Hardware Configuration
  2.2 Converters
      2.2.1 Converter, General Purpose
      2.2.2 Rectifying - Rectification
      2.2.3 Inverting - Inversion
      2.2.4 Converter, d.c. Linked
      2.2.5 Converter, Line-Side Commulated
      2.2.6 Chopper
      2.2.7 Converter, Voltage Source
      2.2.8 Converter, Voltage Source
  2.3 Drive System Operating Characteristics
      2.3.1 Two Quadrant Operation
      2.3.2 Four Quadrant Operation
      2.3.3 Dynamic Braking
      2.3.4 Regeneration
  2.4 CDM, BDM and Converter Input Parameters
      2.4.1 Rated System Voltage U[LN]
      2.4.2 Rated System Frequency f[LN]
      2.4.3 Line-Side Rated a.c. Voltage U[VN]
      2.4.4 Void
      2.4.5 Rated Input Current
      2.4.6 Line-Side Harmonic Content
      2.4.7 Characteristic Current Harmonics
      2.4.8 Harmonic Distortion
      2.4.9 Converter Input Displacement Factor cos[phi][V1]
      2.4.10 Line-Side Displacement Factor cos[phi][V1]
      2.4.11 Input Total Power Factor, lambda[L]
      2.4.12 Maximum a.c. System, Symmetrical Short-Circuit
             Current ISCM
  2.5 CDM, BDM and Converter Output Parameters
      2.5.1 d.c. current l[d]
      2.5.2 Rated Continuous Output Current l[dN]
      2.5.3 Overload Capacity l[dM]
      2.5.4 Continuous Output Rating P[dN]
      2.5.5 Rated Output Voltage U[dN]
      2.5.6 Ripple U[pp], l[pp]
      2.5.7 Load-Side Harmonic Content
      2.5.8 Efficiency of Power Conversion eta[D], eta[C]
      2.5.9 Maximum Field Supply current l[FM]
      2.5.10 Rated Field Supply Voltage U[FN]
  2.6 Converter Circuitry and circuit Elements
      2.6.1 Commutating Capacitor
      2.6.2 Commutating Inductor
      2.6.3 a.c. Filter Network
      2.6.4 Power Factor Correction Network
      2.6.5 d.c. Filter Capacitor
  2.7 Motors
      2.7.1 d.c. Motors Types
      2.7.2 Rated Hot Field Voltage
      2.7.3 Base Speed N[0]
      2.7.4 Maximum Safe Motor Speed
      2.7.5 Torque Pulsation
  2.8 Control Systems
      2.8.1 Controlled Variable
      2.8.2 Service Variable
      2.8.3 Operating Variable
      2.8.4 Feedback Control System Variables
3 FUNDAMENTAL FEATURES
  3.1 Operational
  3.2 Fault Supervision
  3.3 Minimum Status Indication Required
  3.4 I/O Devices
4 SERVICE CONDITIONS
  4.1 Installation and Operation
      4.1.1 Electrical Service Conditions
      4.1.2 Environmental Service Conditions
      4.1.3 Unusual Environmental Service Conditions
      4.1.4 Installation, Compressing and Operation
  4.2 Storage of Equipment
      4.2.1 Climatic Conditions
      4.2.2 Specific Storage Hazards
  4.3 Transportation
      4.3.1 Climatic Conditions
      4.3.2 Unusual Climatic Conditions
      4.3.3 Mechanical Conditions
5 RATINGS
  5.1 BDM Input Ratings
      5.1.1 Input Voltages
      5.1.2 Input Currents
  5.2 BDM Output Ratings
      5.2.1 Continuous Output Ratings
      5.2.2 Overload Capacity
      5.2.3 Speed Range
      5.2.4 Existing d.c. Voltage Ratings
  5.3 Efficiency and Losses
  5.4 Ripple
  5.5 Transformers and Reactors
6 PERFORMANCE REQUIREMENTS
  6.1 Steady-state Performance
      6.1.1 Deviation Band
      6.1.2 Selection of Deviation Bands (Steady-State)
      6.1.3 Service Deviation Band-Limits
      6.1.4 Operating Deviation Band-Limits
      6.1.5 Resolution
  6.2 Dynamic Performance
  6.3 Dynamic Braking and Dynamic Slowdown
      6.3.1 Dynamic Braking
      6.3.2 Dynamic Slowdown
  6.4 Other Performance Requirements
      6.4.1 Use of the Drive in the Application
      6.4.2 Use of the Drive in its Connection to Supply
      6.4.3 Ratings
      6.4.4 Protective Devices
7 Tests
  7.1 Classification of Tests
      7.1.1 Types Test
      7.1.2 Routine Test
      7.1.3 Sampling Test
      7.1.4 Special Test
      7.1.5 Workshop Test
      7.1.6 Acceptance Test
      7.1.7 Commissioning Test
      7.1.8 Witness Test
  7.2 Performance of Tests
      7.2.1 General Conditions
      7.2.2 Earthing Conditions
  7.3 Items of Separate Device Tests
      7.3.1 Standard Tests for PDS
      7.3.2 Standard Tests for CDM/BDM
      7.3.3 Checking the Properties of the Equipment of
             CDM/BDM
  7.4 Items of Power Drive Systems Tests
      7.4.1 Test Set-Up
      7.4.2 Definitions of Rating Tests
      7.4.3 Definitions of Dynamic Tests
8 PRODUCT INFORMATION
  8.1 Marking
  8.2 Information to be Supplied With the PDS or CDM/BDM
      8.2.1 Information to be Supplied With the Furnished
             Equipment
      8.2.2 Information to be Supplied or Made Available
      8.2.3 Speed Information to Be Supplied With the Power
             Drive System
9 SAFETY AND WARNING LABELS
  9.1 Warning Labels
  9.2 Safety and Nature of a PDS
Annexes
Annex A - MOTOR CONSIDERATIONS
Annex B - LINE-SIDE CONSIDERATIONS
Annex C - AUXILIARY EQUIPMENT
Annex D - CONTROL STRATEGIES
Annex E - TOPOLOGIES
Annex G - MONITORING FEATURES

Applies to general purpose adjustable speed dc drive systems that include the power conversion, control equipment and a motor or motors.