• There are no items in your cart

NEMA MG 1 : 2016

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

MOTORS AND GENERATORS

Superseded date

25-10-2022

Published date

23-11-2012

Foreword
Section I - GENERAL STANDARDS APPLYING TO ALL MACHINES
            Part 1 - REFERENCED STANDARDS AND DEFINITIONS
Section I - GENERAL STANDARDS APPLYING TO ALL MACHINES
            Part 2 - TERMINAL MARKINGS
Section I - GENERAL STANDARDS APPLYING TO ALL MACHINES
            Part 3 - HIGH-POTENTIAL TESTS
Section I - GENERAL STANDARDS APPLYING TO ALL MACHINES
            Part 4 - DIMENSIONS, TOLERANCES, AND MOUNTING
Section I - GENERAL STANDARDS APPLYING TO ALL MACHINES
            Part 5 - ROTATING ELECTRICAL MACHINES -
            CLASSIFICATION OF DEGREES OF PROTECTION
            PROVIDED BY ENCLOSURES FOR ROTATING MACHINES
Section I - GENERAL STANDARDS APPLICABLE TO ALL MACHINES
            Part 6 - ROTATING ELECTRICAL MOTORS - METHODS
            OF COOLING (IC CODE)
Section I - GENERAL STANDARDS APPLYING TO ALL MACHINES
            Part 7 - MECHANICAL VIBRATION-MEASUREMENT,
            EVALUATION AND LIMITS
Section I - GENERAL STANDARDS APPLYING TO ALL MACHINES
            Part 9 - ROTATING ELECTRICAL MOTORS - SOUND
            POWER LIMITS AND MEASUREMENT PROCEDURES
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 10 - AC SMALL AND MEDIUM MOTORS
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 10 - DC SMALL AND MEDIUM MOTORS
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 12 - TESTS AND PERFORMANCE - AC
             AND DC MOTORS
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 12 - TESTS AND PERFORMANCE - AC
             MOTORS
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 12 - TESTS AND PERFORMANCE - DC
             SMALL AND MEDIUM MOTORS
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 13 - FRAME ASSIGNMENTS FOR
             ALTERNATING CURRENT INTEGRAL HORSEPOWER
             INDUCTION MOTORS
SECTION II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL
             MACHINES) Part 14 - APPLICATION DATA - AC AND
             DC SMALL AND MEDIUM MACHINES
SECTION II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 14 - APPLICATION DATA - AC SMALL
             AND MEDIUM MOTORS
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 14 - APPLICATION DATA - DC SMALL
             AND MEDIUM MOTORS
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 15 - DC Generators
Section II - SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL)
             MACHINES Part 18 - DEFINITE PURPOSE MACHINES
Section III - LARGE MACHINES Part 20 - LARGE MACHINES
              - INDUCTION MACHINES
Section III - LARGE MACHINES Part 21 - LARGE MACHINES
              - SYNCHRONOUS MOTORS
Section III - LARGE MACHINES Part 23 - LARGE MACHINES
              - DC MOTORS LARGER THAN 1.25 HORSEPOWER
              PER RPM, OPEN TYPE
Section III - LARGE MACHINES Part 24 - LARGE MACHINES
              - DC GENERATORS LARGER THAN 1.0 KILOWATT
              PER RPM, OPEN TYPE CLASSIFICATION
Section IV - PERFORMANCE STANDARDS APPLYING TO ALL
             MACHINES Part 30 - APPLICATION CONSIDERATIONS
             FOR CONSTANT SPEED MOTORS USED ON A SINUSOIDAL
             BUS WITH HARMONIC CONTENT AND GENERAL PURPOSE
             MOTORS USED WITH ADJUSTABLE-VOLTAGE OR
             ADJUSTABLE-FREQUENCY CONTROLS OR BOTH
Section IV - PERFORMANCE STANDARDS APPLYING TO ALL MACHINES
             Part 31 - DEFINITE-PURPOSE INVERTER-FED POLYPHASE
             MOTORS
Section IV - PERFORMANCE STANDARDS APPLYING TO ALL MACHINES
             Part 32 - SYNCHRONOUS GENERATORS (EXCLUSIVE OF
             GENERATORS COVERED BY ANSI STANDARDS C50.12,
             C50.13, C50.14, AND C50.15 ABOVE 5000 kVA) RATINGS
Section IV - PERFORMANCE STANDARDS APPLYING TO ALL MACHINES
             Part 33 - DEFINITE PURPOSE SYNCHRONOUS GENERATORS
             FOR GENERATING SET APPLICATIONS

Includes practical information concerning performance, safety, testing, and construction and manufacture of ac and dc motors and generators.

DevelopmentNote
Supersedes NEMA MG 13 (05/2002) Also available as a Network CD format. (09/2016)
DocumentType
Standard
PublisherName
National Electrical Manufacturers Association
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
BS 2048-1:1961 Identical

MIL-PRF-62331 Revision A:1997 PUMP ASSEMBLY, BILGE, ELECTRIC MOTOR DRIVEN, DIRECT CURRENT
MIL-B-18897 Revision F:1990 BOILERS, STEAM AND HOT WATER, WATERTUBE (STRAIGHT BARE AND FINNED TUBE), CAST IRON AND FIREBOX, PACKAGED TYPE (40,000 TO 35,000 BTU/HR THERMAL OUTPUT CAPACITY)
MIL-H-4607 Revision E:1987 HEATER, ENGINE AND SHELTER, GROUND
IEEE 1415 : 2006 INDUCTION MACHINERY MAINTENANCE TESTING AND FAILURE ANALYSIS
API STD 541 : 2014 FORM-WOUND SQUIRREL CAGE INDUCTION MOTORS - 375 KW (500 HORSEPOWER) AND LARGER
API 670 : 2014 MACHINERY PROTECTION SYSTEMS
ASME OM : 2017 OPERATION AND MAINTENANCE OF NUCLEAR POWER PLANTS
NFPA 70B : 2016 RECOMMENDED PRACTICE FOR ELECTRICAL EQUIPMENT MAINTENANCE
A-A-59200 Base Document:1998 GRINDING MACHINES, SURFACE, ROTARY TABLE, VERTICAL SPINDLE
A-A-50304 Base Document:1987 DYNAMOMETER, ENGINE RUN-IN, 500 HORSEPOWER CAPACITY
A-A-59330 Base Document:1998 Grinding Machine, Surface, Reciprocating-Table, Horizontal-Spindle, Power-Feed
MIL-B-9925 Revision D:1988 BORING MACHINES, JIB, VERTICAL, SINGLE COLUMN AND DOUBLE COLUMN BRIDGE TYPES, MANUAL AND POWER FEED
CLC/TS 60034-31:2011 Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
MIL-B-44037 Revision A:1986 BLENDER, POWERED MIX, MECHANICALLY REFRIGERATED
MIL-PRF-52109 Revision H:2010 PUMPING ASSEMBLIES, PORTABLE, BULK TRANSFER FUEL AND WATER PUMPING SERVICE
GGG-L-795 Revision E:1990 LUBRICATING UNIT, POWER OPERATED, AND PUMPING UNITS, PRESSURE LUBRICATING, DRUM MOUNTING
MIL-S-80224 Revision A:1989 SHEARING MACHINE, METAL NOTCHING, POWER DRIVEN
IEEE 1531-2003 IEEE Guide for Application and Specification of Harmonic Filters
MIL-B-17452 Revision E:1990 BOILERS, STEAM AND HOT WATER, FIRETUBE - SCOTCH PACKAGED TYPE (320,001 TO 35,000,000 BTU/HR THERMAL OUTPUT CAPACITY)
MIL DTL 0053133 : B NOTICE 1 GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS, GENERAL SPECIFICATION FOR
MIL-C-13962 Revision B:1966 CRUSHING, SCREENING, AND WASHING PLANTS, DIESEL-ENGINE AND ELECTRIC-MOTOR DRIVEN, 225-TONS PER HOUR
MIL-F-80258 Revision A:1986 FURNACES, HEAT-TREATING, ELECTRIC, NATURAL ATMOSPHERE, BOX TYPE
MIL-PRF-24755 Revision B:2010 Fans, Vaneaxial, High Pressure, Naval Shipboard
IEEE 95-2002 IEEE Recommended Practice for Insulation Testing of AC Electric Machinery (2300 V and Above) With High Direct Voltage
MIL-L-80277 Base Document:1989 LATHES, PRECISION, TOOLROOM, VARIABLE SPEED, 11-INCH THROUGH 13-INCH
IEEE 334 : 2007 QUALIFYING CONTINUOUS DUTY CLASS 1E MOTORS FOR NUCLEAR POWER GENERATING STATIONS
IEEE 45.1-2017 IEEE Recommended Practice for Electrical Installations on Shipboard--Design
ANS 57.7 : 88(R1997) DESIGN CRITERIA FOR AN INDEPENDENT SPENT FUEL STORAGE INSTALLATION (WATER POOL TYPE)
API 687 : 2001 : R2009 ROTOR REPAIR
MIL-C-10933 Revision E:1985 CHILLED WATER UNITS, BAKERY
MIL-B-23170 Revision A:1978 BOILERS, STEAM, HIGH PRESSURE WATER TUBE, PACKAGED TYPE (5,000 TO 50,000 POUNDS PER HOUR, FIRED BY COAL, OIL, GAS OR COMBINATION OIL/GAS)
API 687 : 2001 ROTOR REPAIR
HI 2.3 : 2013 ROTODYNAMIC VERTICAL PUMPS OF RADIAL, MIXED, AND AXIAL FLOW TYPES FOR DESIGN AND APPLICATION
AWWA C542 : 2016 ELECTRIC MOTOR ACTUATORS FOR VALVES AND SLIDE GATES
MIL-P-52327 Revision C:1990 PUMPS, CENTRIFUGAL, ELECTRIC-MOTOR-DRIVEN, POSITIVE PRIME, PETROLEUM PRODUCTS, AIRFIELD DEFUELLING AND RECEIVING
MIL-C-13874 Revision K:1992 COMPRESSORS, RECIPROCATING AND ROTARY, AIR, ELECTRIC MOTOR DRIVEN
IEEE 946-2004 IEEE Recommended Practice for the Design of DC Auxiliary Power Systems for Generating Systems
IEEE 1147-2005 IEEE Guide for the Rehabilitation of Hydroelectric Power Plants
MIL-S-80271 Revision A:1992 SHEARING MACHINE, METAL SQUARING MECHANICAL DRIVE
F-B-2903 Base Document:1998 BOILERS, STEAM AND HOT WATER, FIRETUBE, SCOTCH PACKAGED TYPE (320,001 TO 35,000,000 BTU/HR THERMAL OUTPUT CAPACITY)
IEEE 1547.2 : 2008 APPLICATION GUIDE FOR IEEE STD 1547[TM], IEEE STANDARD FOR INTERCONNECTING DISTRIBUTED RESOURCES WITH ELECTRIC POWER SYSTEMS
ASHRAE GHCDGS HEAT PUMP SYSTEMS : 2014 ERRATA 2016 GEOTHERMAL HEATING AND COOLING DESIGN OF GROUND-SOURCE HEAT PUMP SYSTEMS
A-A-59459 Base Document:1999 GRINDING MACHINE, TOOL AND CUTTER, COMPUTER NUMERICAL CONTROL (CNC)
ASME AG-1 : 2019 CODE ON NUCLEAR AIR AND GAS TREATMENT
MIL-HDBK-117 Base Document:1991 Motors, Electric, Small Acquisition, Operations and Support for Primer (No S/S Document)
OO-M-340 Revision F:2004 MILLING, GRINDING, DRILLING, SLOTTING ATTACHMENT
MIL-F-80233 Revision B:1985 FURNACES, VACUUM, HEAT TREATING INTEGRAL QUENCH
CSA C392 : 2011 TESTING OF THREE-PHASE SQUIRREL CAGE INDUCTION MOTORS DURING REFURBISHMENT
MIL G 53133 : B GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS, GENERAL SPECIFICATION FOR
GGG-S-58 Revision F:1993 Saw, Radial Overarm, Woodworking (No S/S Document)
MIL-B-18796 Revision F:1984 BURNERS, SINGLE: OIL, GAS, AND GAS-OIL COMBINATION FOR PACKAGED BOILERS (320,001 TO 125,000,000 BTU/HR THERMAL OUTPUT CAPACITY)
MIL-G-19826 Revision F:1984 GENERATOR SET, DIESEL ENGINE, ALTERNATING CURRENT FOR FACILITIES CONSTRUCTION, 1O KW THRU 500 KW (NOT STOCKED)
EEMUA 151 : 1987 LIQUID RING VACUUM PUMPS AND COMPRESSORS
EN ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems (ISO 10438-2:2007)
A-A-50138 Base Document:1988 FREEZER, MECHANICAL, FOOD
MIL-M-80016 Revision C:1988 MILLING MACHINE, VERTICAL, SWIVEL HEAD, KNEE AND COLUMN, RAM AND TURRET TYPE
MIL-D-80002 Revision E:1989 DRILLING MACHINE, UPRIGHT FLOOR TYPE, ROUND & BOX COLUMN, SLIDING HEAD, PLAIN TABLE, POWER FEED
IEEE 902-1998 IEEE Guide for Maintenance, Operation, and Safety of Industrial and Commercial Power Systems (Yellow Book)
API 611 : 2008 GENERAL-PURPOSE STEAM TURBINES FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
IEEE 141 : 1993 IEEE Recommended Practice for Electric Power Distribution for Industrial Plants
SAE ARP 5015 : 2011 GROUND EQUIPMENT - 400 HERTZ GROUND POWER PERFORMANCE REQUIREMENTS
A-A-59415 Base Document:1999 Grinding Machine, Universal, Vertical-Spindle, Nontraversing Rotary Table, Computer Numerical Control (CNC)
A-A-59460 Base Document:2000 PLATING UNIT, SELECTIVE (BRUSH), PORTABLE
A-A-59472 Base Document:1999 TUMBLER, DRYING, LAUNDRY (NAVAL SUBMARINE)
IEEE DRAFT 67 : D5 2005 GUIDE FOR THE OPERATION AND MAINTENANCE OF TURBINE GENERATORS
CSA C392 : 2011 : INC : UPD 1 : 2011 TESTING OF THREE-PHASE SQUIRREL CAGE INDUCTION MOTORS DURING REFURBISHMENT
API 14FZ : 2013 RECOMMENDED PRACTICE FOR DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, ZONE 0, ZONE 1, AND ZONE 2 LOCATIONS
A-A-59332 Revision A:2013 GRINDING MACHINE, CYLINDRICAL, EXTERNAL, CENTER-TYPE, COMPUTER NUMERICAL CONTROL (CNC)
A-A-59618 Base Document:2002 Cleaner, Pressure, Hot-Water, Skid-Mounted
A-A-59469 Base Document:1999 Washer-Extractor, Laundry, 35 to 200 Pound Capacity (Naval Shipboard)
MIL-S-24036 Revision E:1989 SAWS, BAND, CUTOFF, HORIZONTAL, NON-ADJUSTABLE & ADJUSTABLE CUTTING ANGLE
OO-L-2880 Base Document:1997 LAUNDRY UNIT, SKID-MOUNTED, 100 POUNDS (DRY WEIGHT) PER HOUR
MIL-HDBK-705 Revision C:1987 GENERATOR SETS, ELECTRICAL, MEASUREMENTS AND INSTRUMENTATIONS
MIL-F-80133 Revision B:1987 FURNACES, HEAT TREATING, PIT TYPE, ELECTRIC, FORCED CONVECTION
API 11P : 1989 SPECIFICATION FOR PACKAGED RECIPROCATING COMPRESSORS FOR OIL AND GAS PRODUCTION SERVICES
A-A-50314 Base Document:1997 Boring Machines, Engine Cylinder (Portable)
F-P-2908 Base Document:1997 PUMPING UNIT, CONDENSATE, RETURN, AND BOILER FEED PACKAGE
IEEE 1100 : 2005 POWERING AND GROUNDING ELECTRONIC EQUIPMENT
IEEE 242-2001 IEEE Recommended Practice for Protection and Coordination of Industrial and Commercial Power Systems (IEEE Buff Book)
MIL-PRF-19004 Revision B:2001 FANS, CENTRIFUGAL, VENTILATION, NAVAL SHIPBOARD
API 14F : 2008 : R2013 DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, DIVISION 1 AND DIVISION 2 LOCATIONS
API 540:1999 ELECTRICAL INSTALLATIONS IN PETROLEUM PROCESSING PLANTS
MIL-P-53065 Base Document:1986 PUMPING UNIT, FRAME MOUNTED, 1-1/2 INCH, ELECTRIC MOTOR DRIVEN, 35 GPM AT 25 FEET TOTAL HEAD
MIL-M-80255 Revision B:1990 MACHINING CENTERS, VERTICAL, SINGLE SPINDLE, COMPUTER NUMERICAL CONTROL (CNC)
IEEE DRAFT 1147 : D8 2005 GUIDE FOR THE REHABILITATION OF HYDROELECTRIC POWER PLANTS
MIL-C-3925 Revision H:1989 COMPRESSOR, RECIPROCATING AND ROTARY POWER DRIVEN, AIR [PAINT SPRAY TYPE]
MIL-PRF-80095 Revision E:2015 SAWS, BAND, WOODWORKING
MIL-W-80119 Revision B:1971 WELDING SYSTEMS, ELECTRON BEAM, VACUUM TYPE, COMPUTER NUMERICALLY CONTROLLED (CNC)
ICC IECC CODE AND COMMENTARY : 2015 IECC® Code and Commentary
MIL-G-52884 Revision A:1981 GENERATOR SETS, DIESEL ENGINE DRIVEN, 15 THRU 200 KILOWATTS 50/60 & 400 HERTZ, (TACTICAL)
CSA C392 : 2011 : INC : UPD 2 : 2012 TESTING OF THREE-PHASE SQUIRREL CAGE INDUCTION MOTORS DURING REFURBISHMENT
MIL-P-80172 Revision C:1988 PUNCHING MACHINE, METAL SINGLE END TYPE, NUMERICALLY CONTROLLED
MIL-P-80186 Revision B:1991 POSITIONERS, WELDING, ROTATING TABLE, CANTILEVER ARM DESIGN
A-A-59393 Base Document:2000 MILLING MACHINE, VERTICAL MULTISPINDLE, DOUBLE COLUMN, COMPUTER NUMERICAL CONTROL (CNC)
IEEE C62.21 : 2003 GUIDE FOR THE APPLICATION OF SURGE VOLTAGE PROTECTIVE EQUIPMENT ON AC ROTATING MACHINERY 1000 V AND GREATER
ASHRAE HDBK REFRIGERATION : 2014 ASHRAE HANDBOOK - REFRIGERATION
MIL-DTL-38195 Revision D:2000 Generator Set, Gas Turbine Engine, 60 KW 400 Hertz, General Purpose
MIL-B-29205 Revision A:1990 BOILERS, FLUIDIZED BED, STEAM AND HOT WATER, PACKAGED TYPE (330 TO 51,500 POUNDS PER HOUR THERMAL OUTPUT CAPACITY)
ASME BTH 1 : 2017 DESIGN OF BELOW-THE-HOOK LIFTING DEVICES
MIL-B-26994 Revision E:1992 BALANCER, VEHICLE WHEEL, ON-VEHICLE TYPE
MIL S 4880 : G NOTICE 1 SWEEPER, MAGNET, SELF-PROPELLED
MIL-PRF-23798 Revision D:2004 Air Conditioner, Fan-Coil Assembly
OO-J-571 Revision F:2015 JOINTERS, WOODWORKING
ASHRAE 90.4 : 2016 ENERGY STANDARD FOR DATA CENTERS
MIL-B-28685 Base Document:1990 BAGHOUSE, REVERSE PULSE JET; FOR PACKAGED BOILEK3 FIRED ON COAL OR A COMBINATION OF COAL AND GAS, COAL AND OIL, OR COAL-GAS-OIL (2,000,000 TO 125,000,000 BTU/HR THERMAL OUTPUT CAPACITY)
A-A-59190 Base Document:1998 Cold Food Counter, Mechanically Refrigerated (Naval Shipboard)
MIL-P-80279 Base Document:1991 PUNCHING, SHEARING, NOTCHING, AND COPING MACHINE, METAL, HYDRAULIC DRIVEN, FOUR STATION TYPE
MIL-P-80280 Base Document:1991 PUNCHING, ANGLE AND BAR SHEARING MACHINE, METAL, HYDRAULICALLY DRIVEN, THREE STATION TYPE
MIL-DTL-53133 Revision C:2002 GENERATOR SETS, SKID MOUNTED, TACTICAL, QUIET, DIESEL ENGINE DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS
AWWA E103 : 2015 HORIZONTAL AND VERTICAL LINE-SHAFT PUMPS
NFPA 1901:2016 AUTOMOTIVE FIRE APPARATUS
(INACTIVE RECORD)IEEE C50.12 : 2005 SALIENT-POLE 50 HZ AND 60 HZ SYNCHRONOUS GENERATORS AND GENERATOR/MOTORS FOR HYDRAULIC TURBINE APPLICATIONS RATED 5 MVA AND ABOVE
IEEE 741-2007 IEEE Standard Criteria for the Protection of Class 1E Power Systems and Equipment in Nuclear Power Generating Stations
ASME AG 1 : 2012 CODE ON NUCLEAR AIR AND GAS TREATMENT
MIL-L-23251 Revision E:1989 LATHES, ENGINE AND TOOLROOM 2516 AND 3220
MIL-PRF-26139 Revision E:2015 TESTER, PRESSURIZED CABIN LEAKAGE, AIRCRAFT, (AF/M24T-3 AND AF/M32T-1)
MIL-F-80113 Revision D:1988 FURNACE, VACUUM, HEAT TREATING AND BRAZING
F-S-2911 Base Document:1997 STOKERS, MECHANICAL - FOR PACKAGED BOILERS FIRED ON COAL OR A COMBINATION OF COAL-GAS, COAL-OIL, OR COAL-GAS-OIL (2,000 TO 50,000,000 BTU/HR THERMAL OUTPUT CAPACITY)
API 611 : 2008 : R2014 GENERAL-PURPOSE STEAM TURBINES FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
IEEE 1349-2011 REDLINE IEEE Guide for Application of Electric Motors in Class I, Division 2 and Class I, Zone 2 Hazardous (Classified) Locations
MIL-B-12570 Revision D:1977 BAKERY OVEN, TRAILER MOUNTED, M-533
A-A-59471 Base Document:1999 Dry Cleaning Presses and Finishing Equipment (Naval Shipboard)
A-A-59412 Revision A:2013 SWAGING MACHINE, ROTARY, FLOOR-MOUNTED
API 618 : 2007 : R2016 RECIPROCATING COMPRESSORS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
A-A-59392 Base Document:1999 GRINDING MACHINES, SURFACE, ROTARY TABLE, HORIZONTAL SPINDLE
MIL-S-3788 Revision G:1991 SHAPER, WOODWORKING
MIL-P-17552 Revision F:1991 PUMP UNITS, CENTRIFUGAL, WATER, HORIZONTAL, GENERAL SERVICE AND BOILER FEED, ELECTRIC MOTOR OR STEAM TURBINE DRIVEN
HI 1.3 : 2013 ROTODYNAMIC CENTRIFUGAL PUMPS FOR DESIGN AND APPLICATION
F-B-2902 Base Document:1990 BOILERS, STEAM WATERTUBE (BENT TUBE, MULTI-DRUM AND CROSS DRUM) PACKAGED TYPE (10,000,000 TO 125,000,000 BTU/HR THERMAL OUTPUT CAPACITY)
EN 60034-30:2009 Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
MIL-L-13896 Revision E:1987 LATHES, ENGINE, GAP, SLIDING BED AND REMOVABLE BLOCK
EN ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2007)
API 540 : 1999 : R2006 ELECTRICAL INSTALLATIONS IN PETROLEUM PROCESSING PLANTS
IEEE C37.06-2009 IEEE Standard for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis--Preferred Ratings and Related Required Capabilities for Voltages Above 1000 V
KKK-S-2922 Base Document:1997 SEMITRAILER, VAN; COMMERCIAL (FURNITURE, PERSONNEL, REFRIGERATOR, CARGO, AND SIDE CURTAIN) 7 TO 35 TON
API TR 11L6 : 2008 TECHNICAL REPORT ON ELECTRIC MOTOR PRIME MOVER FOR BEAM PUMPING UNIT SERVICE
ASHRAE 189.1 : 2014 DESIGN OF HIGH-PERFORMANCE GREEN BUILDINGS
OO-P-2895 Base Document:1997 PLANT, AGGREGATE, SECONDARY, WITH CONE CRUSHER, MOBILE, 75 TON PER HOUR CAPACITY
MIL-W-44167 Revision B:1992 WASHING MACHINE, LAUNDRY: OPEN END TYPE, TRAILER MOUNTED
IEEE 43-2013 REDLINE IEEE Recommended Practice for Testing Insulation Resistance of Electric Machinery
MIL-PRF-24751 Revision A:2004 FANS, VANEAXIAL GAS TURBINE ENCLOSURE COOLING NAVAL SHIPBOARD
MIL-P-80054 Revision D:1988 PUNCHING MACHINE, METAL, TURRET TYPE, NUMERICALLY CONTROLLED
MIL-B-18966 Revision C:1984 BLOCKING PLANT, CONCRETE
IEEE 551 : 2006 CALCULATING SHORT-CIRCUIT CURRENTS IN INDUSTRIAL AND COMMERCIAL POWER SYSTEMS
MIL-H-82000 Revision C:1990 HEATER, HOT OIL, 1.5, 3 AND 5 MILLION BTU/H OUTPUT, SKID MOUNTED
A-A-52139 Base Document:1993 ICE MAKING MACHINE, CUBE
MIL M 29212 : B NOTICE 1 MIXING PLANT, ASPHALT, DRUM TYPE, PORTABLE, ELECTRIC MOTOR DRIVEN, 120 TONS PER HOUR CAPACITY
MIL-B-17095 Revision H:1990 BOILERS, STEAM, WATERTUBE (BENT TUBE, MULTI-DRUM AND CROSS DRUM) PACKAGED TYPE (10,000,000 TO 125,000,000 BTU/HR THERMAL OUTPUT CAPACITY)
API 687 : 2001 : R2015 ROTOR REPAIR
CSA C392 : 2011 : R2016 TESTING OF THREE-PHASE SQUIRREL CAGE INDUCTION MOTORS DURING REFURBISHMENT
MIL-PRF-24775 Revision A:2005 Air Conditioning Fan Coil Units, Horizontal and Vertical Types, Naval Shipboard
A-A-59285 Base Document:1999 Saws, Power, Hack
PD IEC/TS 60034-30-2:2016 Rotating electrical machines Efficiency classes of variable speed AC motors (IE-code)
NFPA 79 : 2018 ELECTRICAL STANDARD FOR INDUSTRIAL MACHINERY
MIL-DTL-53135 Base Document:1996 AUXILIARY POWER UNIT, 10 KW, 120/240 VAC, 60 HZ
A-A-59384 Revision B:2014 PRESS, 'H' FRAME, HYDRAULIC
MIL-L-80007 Revision E:1989 LATHES, TOOLROOM, 11-INCH THROUGH 13-INCH
API 546 : 2008 BRUSHLESS SYNCHRONOUS MACHINES - 500 KVA AND LARGER
FM 1312 : 2018 CENTRIFUGAL FIRE PUMPS (VERTICAL-SHAFT, TURBINE TYPE)
API 618 : 2007 RECIPROCATING COMPRESSORS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
MIL-PRF-18953 Revision C:2005 FANS, VANEAXIAL AND TUBEAXIAL, VENTILATION AND AIR CONDITIONING, NAVAL SHIPBOARD
MIL-P-80276 Base Document:1988 PRESS BRAKES, HYDRAULICALLY OPERATED, SHEET AND PLATE, COMPUTER NUMERICALLY CONTROLLED (CNC)
A-A-59266 Base Document:1998 Grinding Machine, Universal, Cylindrical, External, Center-Type
API 614 : 2008 LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES
API 14F:2008 DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, DIVISION 1 AND DIVISION 2 LOCATIONS
MIL-B-45022 Revision F:1992 BLAST CLEANING CABINETS
MIL-PRF-43001 Revision G:2016 WASHER-EXTRACTORS, LAUNDRY, COMMERCIAL
F-B-2910 Base Document:1998 BURNERS, SINGLE: OIL, GAS, AND GAS-OIL COMBINATION FOR PACKAGED BOILERS (320,001 TO 125, 000,000 BTU/HR THERMAL OUTPUT CAPACITY)
EN 60034-30-1:2014 Rotating electrical machines - Part 30-1: Efficiency classes of line operated AC motors (IE code)
MIL-P-80104 Revision D:1990 PRESSES, SWAGING, WIRE ROPE FITTING, HYDRAULIC POWERED, ELECTRIC MOTOR DRIVEN
IEEE C37.16-2009 REDLINE IEEE Standard for Preferred Ratings,Related Requirements, and Application Recommendations for Low-Voltage AC (635 V and below)and DC (3200 V and below) Power Circuit Breakers
MIL-DTL-32496 Base Document:2014 GENERATOR SETS, SKID MOUNTED, TRAILER MOUNTED ADVANCED MEDIUM-SIZED MOBILE POWER SOURCES, TACTICAL DIESEL FUEL DRIVEN, ALTERNATING CURRENT 5 THROUGH 60 KILOWATTS, GENERAL SPECIFICATION FOR
MIL-B-43928 Revision A:1987 BROILER, CONVEYORIZED, INFRARED, ELECTRIC
SAE ARP 1148 : 2013 GROUND ELECTRICAL POWER UNIT, TRANSPORTABLE 115/200 VOLT AC (NOMINAL) 400 HERTZ, 3-PHASE 4-WIRE (GROUNDED NEUTRAL) Y-CONNECTED SYSTEM
WW-F-2743 Revision A:1998 FURNACES, WARM AIR & HEATERS, UNIT, FORCED AIR CIRCULATION, OIL & GAS FIRED
MIL-C-11085 Revision D:1986 CONVEYOR, BELT; (FLAT, SKID-MOUNTED, ELECTRIC-MOTOR-DRIVEN, 24-INCH-WIDE BELT, 50-FOOT-LONG FRAME; CAPACITY, 25 POUNDS PER FOOT, 75 TONS PER HOUR)
CC-G-2745 Base Document:1984 GENERATOR SETS, DIESEL ENGINE, ALTERNATING CURRENT, FOR FACILITIES CONSTRUCTION; 10 KW THROUGH 1000 KW (NOT STOCKED)
MIL-F-80089 Revision B:1986 FURNACES, HEAT-TREATING, GAS-FIRED, BOX-TYPE, DIRECT-FIRED AND FULL-MUFFLE DESIGN
IEEE DRAFT C50.12 : D10 2004 SALIENT-POLE 50 AND 60 HZ SYNCHRONOUS GENERATORS AND GENERATOR/MOTORS FOR HYDRAULIC TURBINE APPLICATIONS RATED 5 MVA AND ABOVE
OO-S-256 Revision K:2012 Sewing Machine, Industrial, General Specification for
OO-S-236 Revision E:2015 SAW, CIRCULAR, TABLE TYPE, WOODWORKING, SINGLE TILTING ARBOR, FLOOR MOUNTED
MIL-D-12491 Revision E:1989 DEGREASER, SOLVENT, TANK IMMERSION TYPE
MIL-B-45081 Revision E:1991 BLAST CLEANING MACHINE: SELF-CONTAINED TUMBLE TYPE, WITH DUST COLLECTOR
XX-C-2816 Revision A:2016 COMPRESSOR, AIR, RECIPROCATING OR ROTARY, ELECTRIC MOTOR DRIVEN, STATIONARY, 10 HP AND LARGER
CSA C390 : 2010(R2015) TEST METHODS, MARKING REQUIREMENTS, AND ENERGY EFFICIENCY LEVELS FOR THREE-PHASE INDUCTION MOTORS
CSA C390 : 2010 : INC : UPD 2 : 2016 :R201500 TEST METHODS, MARKING REQUIREMENTS, AND ENERGY EFFICIENCY LEVELS FOR THREE-PHASE INDUCTION MOTORS
ASTM F 2361 : 2003 : R2009 Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower
CSA C391 : 2015 TESTING OF THREE-PHASE SYNCHRONOUS MACHINES DURING REFURBISHMENT
CSA C390:2010 TEST METHODS, MARKING REQUIREMENTS, AND ENERGY EFFICIENCY LEVELS FOR THREE-PHASE INDUCTION MOTORS
ASTM F 1203 : 2016 : REDLINE Standard Specification for Washing Machines—Pot, Pan, and Utensil, Heat Sanitizing, Commercial Rotary Conveyor Type
ASTM F 857 : 2017 : REDLINE Standard Specification for Hot Water and Chemical Sanitizing Commercial Dishwashing Machines, Stationary Rack Type
BS EN ISO 14224:2016 Petroleum, petrochemical and natural gas industries. Collection and exchange of reliability and maintenance data for equipment
IEC 60034-27-4:2018 Rotating electrical machines - Part 27-4: Measurement of insulation resistance and polarization index of winding insulation of rotating electrical machines
IEEE 115-2009 REDLINE IEEE Guide for Test Procedures for Synchronous Machines Part I—Acceptance and Performance Testing Part II—Test Procedures and Parameter Determination for Dynamic Analysis
C282-15 Emergency electrical power supply for buildings
CSA C22.2 No. 100 : 2014 MOTORS AND GENERATORS
CSA C390 : 2010 : R2015 TEST METHODS, MARKING REQUIREMENTS, AND ENERGY EFFICIENCY LEVELS FOR THREE-PHASE INDUCTION MOTORS
CSA C838 : 2013 ENERGY EFFICIENCY TEST METHODS FOR THREE-PHASE VARIABLE FREQUENCY DRIVE SYSTEMS
UFC 3-230-01 : Change 2 UNIFIED FACILITIES CRITERIA - WATER STORAGE, DISTRIBUTION, AND TRANSMISSION
BS EN 60034-30:2009 Rotating electrical machines Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
NEMA ICS 20:2009 (R2015) Informational Guide to Electrical Industrial Topics
IEEE 434-2006 IEEE Guide for Functional Evaluation of Insulation Systems for AC Electric Machines Rated 2300 V and Above
NEMA ICS 61800-2:2005 Adjustable Speed Electrical Power Drive Systems, Part 2: General Requirements—Rating Specifications for Low Voltage Adjustable Frequency AC Power Drive Systems
NEMA MGW 1-2013 THE U.S. DEPARTMENT OF ENERGY SMALL ELECTRIC MOTOR STANDARDS FINAL RULE AND TECHNICAL SUPPORT DOCUMENT OF MARCH 9, 2010
ASTM F 1433 : 1997 Standard Specification for Mechanically Refrigerated Shipboard Air Conditioner
NEMA MG 2:2014 Safety Standard for Construction and Guide for Selection, Installation and Use of Electric Motors and Generators
NEMA SM 24-1991 (R1997, R2002) LAND BASED STEAM TURBINE GENERATOR SETS 0 TO 33,000 kW
NEMA ICS8 : 2011 APPLICATION GUIDE FOR INDUSTRIAL CONTROL AND SYSTEMS CRANE AND HOIST CONTROLLERS
CSA N290.8 : 2015 TECHNICAL SPECIFICATION REQUIREMENTS FOR NUCLEAR POWER PLANT COMPONENTS
ISO 20958:2013 Condition monitoring and diagnostics of machine systems — Electrical signature analysis of three-phase induction motors
A-A-59334 Base Document:1999 Lathe, Engine (Standard) and Toolroom (Precision), Horizontal Spindle
ASTM F 2363/F2363M : 2017 : REDLINE Standard Specification for Sewage and Graywater Flow Through Treatment Systems
IEC 60034-30:2008 Rotating electrical machines - Part 30: Efficiency classes of single-speed, three-phase, cage-induction motors (IE-code)
CSA C747 : 2009 : INC : UPD 1 : 2016 : R201400 ENERGY EFFICIENCY TEST METHODS FOR SMALL MOTORS
ASTM F 1966 : 2012 Standard Specification for Dough Divider and Rounding Machines
ISO 10436:1993 Petroleum and natural gas industries — General-purpose steam turbines for refinery service
IEC TS 60034-31:2010 Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
ASTM F 2361 : 2003 : R2013 Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower
CSA C390 : 2010 : INC : UPD 1 : 2015 : R201500 TEST METHODS, MARKING REQUIREMENTS, AND ENERGY EFFICIENCY LEVELS FOR THREE-PHASE INDUCTION MOTORS
ASTM F 2361 : 2003 Standard Guide for Ordering Low Voltage (1000 VAC or Less) Alternating Current Electric Motors for Shipboard Service—Up to and Including Motors of 500 Horsepower
NEMA ICS 7.2 : 2015 APPLICATION GUIDE FOR AC ADJUSTABLE SPEED DRIVE SYSTEMS
ISO 14224:2016 Petroleum, petrochemical and natural gas industries Collection and exchange of reliability and maintenance data for equipment
ASTM F 860 : 2007 Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Multiple Tank, Rackless Conveyor Type
CSA C747:2009 ENERGY EFFICIENCY TEST METHODS FOR SMALL MOTORS
NEMA MG 11 : 1977(R2012) ENERGY MANAGEMENT GUIDE FOR SELECTION AND USE OF SINGLE-PHASE MOTORS
ASTM F 1202 : 2016 : REDLINE Standard Specification for Washing Machines, Heat Sanitizing, Commercial, Pot, Pan, and Utensil Vertically Oscillating Arm Type
NEMA MG 3-1974 (R1995, R2000, R2006, R2012, R2014, R2021) Sound Level Prediction for Installed Rotating Electrical Machines
ASTM F 860 : 2007 : R2018 : EDT 1 Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Multiple Tank, Rackless Conveyor Type
ASTM F 1433 : 1997 : R2010 Standard Specification for Mechanically Refrigerated Shipboard Air Conditioner (Withdrawn 2019)
BS ISO 20958:2013 Condition monitoring and diagnostics of machine systems. Electrical signature analysis of three-phase induction motors
ASTM F 860 : 2007 : R2013 Standard Specification for Hot Water Sanitizing Commercial Dishwashing Machines, Multiple Tank, Rackless Conveyor Type
CSA C747 : 2009 : R2014 ENERGY EFFICIENCY TEST METHODS FOR SMALL MOTORS
BS EN 60034-30-1:2014 Rotating electrical machines Efficiency classes of line operated AC motors (IE code)
A-A-59335 Base Document:1999 Saw, Band, Cutoff, Horizontal, and Combination Horizontal and Vertical
IEEE C37.96-2012 IEEE Guide for AC Motor Protection
BS EN ISO 10438-2:2003 Petroleum and natural gas industries. Lubrication, shaft sealing and control oil systems and auxiliaries Special purpose oil systems
S6-14 Canadian Highway Bridge Design Code
DD CLC/TS 60034-31:2011 Rotating electrical machines Selection of energy-efficient motors including variable speed applications. Application guide
ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries Lubrication, shaft-sealing and control-oil systems and auxiliaries Part 3: General-purpose oil systems
NEMA ICS 2:2008 Controllers, Contactors and Overload Relays Rated 600 V
NEMA ICS 10.2 : 2005 INDUSTRIAL CONTROL AND SYSTEMS - PART 2: STATIC AC TRANSFER EQUIPMENT
NEMA ICS 9 : 1993 INDUSTRIAL CONTROL AND SYSTEMS: POWER CIRCUIT ACCESSORIES
ASTM F 2645 : 2016 : REDLINE Standard Specification for Bun Slicing Machines
NEMA ICS 16:2001 Motion/Position Control Motors, Controls and Feedback Devices
NEMA MG 7 : 93 REV 1 96 MOTION/POSITION CONTROL MOTORS AND CONTROLS
BS ISO 19859:2016 Gas turbine applications. Requirements for power generation
NEMA ICS 10.1 : 2005 INDUSTRIAL CONTROL AND SYSTEMS - PART 1: ELECTROMECHANICAL AC TRANSFER SWITCH EQUIPMENT
BS EN ISO 10438-3:2003 Petroleum, petrochemical and natural gas industries. Lubrication, shaft sealing and control oil systems and auxilliaries General-purpose oil systems
NEMA ICS 61800-1:2002(R2007) Adjustable Speed Electrical Power Drive Systems, Part 1: General Requirements—Rating Specifications for Low Voltage Adjustable-Speed DC Power Drive Systems
ASTM F 2643 : 2015 : REDLINE Standard Specification for Powered Pot, Pan and Utensil Washing Sinks
IEC/IEEE PAS 63547:2011 Interconnecting distributed resources with electric power systems
ASTM F 2646 : 2016 : REDLINE Standard Specification for Bread Slicing Machines
ASTM F 1966 : 2012 : R2017 : EDT 1 Standard Specification for Dough Divider and Rounding Machines
ISO 19859:2016 Gas turbine applications Requirements for power generation
ASTM F 1433 : 1997 : R2004 Standard Specification for Mechanically Refrigerated Shipboard Air Conditioner
ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 2: Special-purpose oil systems
NEMA ICS 7.1:2014 Safety Standards for Construction and Guide for Selection, Installation and Operation of Adjustable Speed Drive Systems
IEEE 1547.1-2005 IEEE Standard Conformance Test Procedures for Equipment Interconnecting Distributed Resources with Electric Power Systems
IEEE 45.6-2016 IEEE Recommended Practice for Electrical Installations on Shipboard--Electrical Testing
IEEE C37.06-2009 AC HIGH-VOLTAGE CIRCUIT BREAKERS RATED ON A SYMMETRICAL CURRENT BASIS - PREFERRED RATINGS AND RELATED REQUIRED CAPABILITIES
ASME HST 4 : 1999 : R2010 PERFORMANCE STANDARD FOR OVERHEAD ELECTRIC WIRE ROPE HOISTS
IEEE 1159-2009 IEEE Recommended Practice for Monitoring Electric Power Quality
IEEE 3004.8-2016 IEEE Recommended Practice for Motor Protection in Industrial and Commercial Power Systems
IEEE 1290-2015 REDLINE IEEE Guide for Motor-Operated Valve (MOV) Motor Application, Protection, Control, and Testing in Nuclear Power-Generating Stations
IEEE 1827-2016 IEEE Guide for Electrical and Control Design of Hydroelectric Water Conveyance Facilities
FM 1043 : 2011 WATER FLOW DETECTOR TESTERS 1 INCH THROUGH 8 INCH NOMINAL SIZE
IEEE 841-2009 IEEE Standard for Petroleum and Chemical Industry--Premium-Efficiency, Severe-Duty, Totally Enclosed Fan-Cooled (TEFC) Squirrel Cage Induction Motors--Up to and Including 370 kW (500 hp)
IEEE 2030.2-2015 IEEE Guide for the Interoperability of Energy Storage Systems Integrated with the Electric Power Infrastructure
ASME HST 4M : 1991 PERFORMANCE STANDARD FOR OVERHEAD ELECTRIC WIRE ROPE HOISTS
PIP RESE001 : 2017 GENERAL PURPOSE SKID-MOUNTED PACKAGED EQUIPMENT SPECIFICATION
API 14F REDLINE : 2008 DESIGN, INSTALLATION, AND MAINTENANCE OF ELECTRICAL SYSTEMS FOR FIXED AND FLOATING OFFSHORE PETROLEUM FACILITIES FOR UNCLASSIFIED AND CLASS 1, DIVISION 1 AND DIVISION 2 LOCATIONS
API 680 : 1ED 87 PACKAGED RECIPROCATING PLANT AND INSTRUMENT AIR COMPRESSORS FOR GENERAL REFINERY SERVICES
API 614 REDLINE : 2008 LUBRICATION, SHAFT-SEALING AND OIL-CONTROL SYSTEMS AND AUXILIARIES
IEEE C37.100.1-2007 IEEE Standard of Common Requirements for High Voltage Power Switchgear Rated Above 1000 V
ASME B73.2 : 2016 Specification for Vertical In-Line Centrifugal Pumps for Chemical Process
IEEE 3001.11-2017 IEEE Recommended Practice for Application of Controllers and Automation to Industrial and Commercial Power Systems
API 11PGT : 1992 RECOMMENDED PRACTICE FOR PACKAGED COMBUSTION GAS TURBINES
IEEE 1566-2015 REDLINE IEEE Standard for Performance of Adjustable-Speed AC Drives Rated 375 kW and Larger
IEEE 1068-2015 REDLINE IEEE Standard for the Repair and Rewinding of AC Electric Motors in the Petroleum, Chemical, and Process Industries
API 611 REDLINE : 2008 GENERAL-PURPOSE STEAM TURBINES FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
ASME HST 4 : 1999 : R2004 PERFORMANCE STANDARD FOR OVERHEAD ELECTRIC WIRE ROPE HOISTS
EEE 602 : 2007 ELECTRIC SYSTEMS IN HEALTH CARE FACILITIES

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.