NF EN 777-1 : 2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MULTI-BURNER GAS-FIRED OVERHEAD RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - PART 1: SYSTEM D - SAFETY
05-10-2021
12-01-2013
Avant-propos
1 Domaine d'application
2 Références normatives
3 Définitions
3.1 système et les éléments le composant
3.2 dispositifs de réglage, de commande et de sécurité
3.3 fonctionnement du système
3.4 combustibles gazeux
3.5 conditions de fonctionnement et de mesure
3.6 pays de destination
4 Classification des systèmes
4.1 Classification selon la nature des gaz utilisés
(catégories)
4.2 Classification suivant les gaz susceptibles d'être
utilisés
4.3 Classification selon le mode d'évacuation des produits
de combustion
5 Exigences de construction
5.1 Généralités
5.2 Exigences pour les dispositifs de réglage, de commande
et de sécurité
5.3 Dispositifs d'allumage
5.4 Brûleur principal
5.5 Points de prises de pression
5.6 Injecteurs
6 Exigences de fonctionnement
6.1 Étanchéité
6.2 Débits calorifiques
6.3 Températures limites
6.4 Allumage, interallumage et stabilité des flammes
6.5 Régulateur de pression du gaz
6.6 Combustion
6.7 Fonctionnement prolongé
7 Méthodes d'essais
7.1 Généralités
7.2 Construction et conception
7.3 Sécurité de fonctionnement
8 Marquage et notices
8.1 Marquage des systèmes et de l'emballage
8.2 Notices
8.3 Présentation
Annexe A (informative) Système D
Annexe B (informative) Situations nationales
Annexe C (informative) Règles d'équivalence
Annexe D (informative) Calcul du débit massique des produits
de combustion
Annexe E (normative) Extrait du projet de norme
prEN 50165:1995 <<Équipement électrique
des appareils non électriques pour
usages domestiques et analogues - Règles
de sécurité>>
Annexe F (informative) Identification du type de gaz en vigueur
dans divers pays
Annexe G (normative) Conditions nationales particulières
Annexe ZA (informative) Articles de la présente norme
européenne concernant les exigences
essentielles ou d'autres dispositions
des Directives UE
Bibliographie
Specifies the requirements and test methods for the construction, safety, classification and marking of non-domestic gas-fired overhead radiant tube heaters incorporated into a multi-burner system with each burner unit under the control of an automatic burner control system. Applicable to Type B[22] systems intended for use in other than domestic dwellings, in which the supply of combustion air and/or the evacuation of the products of combustion is achieved by mechanical means. Applicable to systems which are intended to be type tested.
DevelopmentNote |
Indice de classement: E31-404-1. (04/2002) PR NF EN 777-1 November 2006. (11/2006)
|
DocumentType |
Standard
|
PublisherName |
Association Francaise de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
NBN EN 777-1 : 2009 | Identical |
NS EN 777-1 : 2009 | Identical |
DIN EN 777-1:2009-09 | Identical |
SN EN 777-1 : 2009 | Identical |
EN 777-1:2009 | Identical |
I.S. EN 777-1:2009 | Identical |
BS EN 777-1:2009 | Identical |
UNE-EN 777-1:2009 | Identical |
UNI EN 777-1 : 2009 | Identical |
NEN EN 777-1 : 2009 | Identical |
NF EN 60335-2-102 : 2016 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-102: PARTICULAR REQUIREMENTS FOR GAS, OIL AND SOLID-FUEL BURNING APPLIANCES HAVING ELECTRICAL CONNECTIONS |
NF EN ISO 228-1 : 2003 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
NF ISO 619976 : 1997 | NATURAL GAS - CALCULATION OF CALORIFIC VALUES, DENSITY, RELATIVE DENSITY WOBBE INDEX FROM COMPOSITION |
ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
NF EN 88-1 : 2011 + A1 2016 | PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA |
NF EN 437 : 2003 + A1 2009 | TEST GASES - TEST PRESSURES - APPLIANCE CATEGORIES |
89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
NF EN 126 : 2012 | MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES |
NF EN 60529 : 92 AMD 2 2014 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) |
NF EN 60335-1 : 2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS |
CR 1404:1994 | Determination of emissions from appliances burning gaseous fuels during type-testing |
NF EN 257 : 2011 | MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES |
NF EN ISO 3166-1 : 2014 | CODES FOR THE REPRESENTATION OF NAMES OF COUNTRIES AND THEIR SUBDIVISION - PART 1: COUNTRY CODES |
NF EN 60584-2 : 1993 | THERMOCOUPLES - PART 2: TOLERANCES |
NF EN 10226-1 : 2004 | PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 1: TAPER EXTERNAL THREADS AND PARALLEL INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION |
ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
NF EN 161 : 2011 + A3 2013 | AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES |
NF EN 298 : 2012 | AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS |
NF EN 10226-2 : 2005 | PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 2: TAPER EXTERNAL THREADS AND TAPER INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION |
NF EN 60584-1 : 2014 | THERMOCOUPLES - PART 1: EMF SPECIFICATIONS AND TOLERANCES |
1990/396/EEC : 1990 | COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.