NF EN 777-2 : 2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MULTI-BURNER GAS-FIRED OVERHEAD RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - PART 2: SYSTEM E - SAFETY
05-10-2021
12-01-2013
Avant-propos
1 Domaine d'application
2 Références normatives
3 Termes et définitions
4 Classification des systèmes
5 Exigences de construction
6 Exigences de fonctionnement
7 Méthodes d'essais
8 Marquage et notices
9 Évaluation de la conformité des POCED et de leurs
terminaux associés
Annexe A (informative) Situations nationales
Annexe B (informative) Système E
Annexe C (informative) Règles d'équivalence
Annexe D (informative) Calcul du débit massique des
produits de combustion
Annexe E (informative) Identification des types de gaz
utilisés dans les différents pays
Annexe F (normative) Conditions nationales spécifiques
Annexe G (informative) Exemple de calcul des facteurs
de pondération pour un appareil à plusieurs
allures
Annexe H (informative) Calcul de conversions de NOx
Annexe I (informative) Situations dans les pays dont les
organismes nationaux sont membres associés du CEN
Annexe J (informative) Modèle de plans d'échantillonnage
Annexe K (informative) Détermination des pertes parles
fumées
Annexe ZA (informative) Articles de la présente Norme
européenne traitant des exigences essentielles
ou d'autres dispositions de Directives UE
Annexe ZB (informative) Articles de la présente Norme
européenne concernant les dispositions de la
Directive UE Produits de construction
Bibliographie
Specifies the requirements and test methods for the construction, safety, classification and marking of non-domestic gas-fired overhead radiant tube heaters incorporated into a multi-burner system with each burner unit under the control of an automatic burner control system. Applicable to Type B[22] and Type B[23] systems intended for use in other than domestic dwelling, in which the supply of combustion air and/or evacuation of the products of combustion is achieved by mechanical means. Applicable to systems which are intended to be type tested.
| DevelopmentNote |
Indice de classement: E31-404-2. (04/2002) PR NF EN 777-2 November 2006. (11/2006)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| BS EN 777-2:2009 | Identical |
| I.S. EN 777-2:2009 | Identical |
| UNI EN 777-2 : 2009 | Identical |
| NS EN 777-2 : 2009 | Identical |
| SN EN 777-2 : 2009 | Identical |
| UNE-EN 777-2:2009 | Identical |
| DIN EN 777-2:2009-09 | Identical |
| NBN EN 777-2 : 2009 | Identical |
| EN 777-2:2009 | Identical |
| NEN EN 777-2 : 2009 | Identical |
| NF EN 60335-2-102 : 2016 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-102: PARTICULAR REQUIREMENTS FOR GAS, OIL AND SOLID-FUEL BURNING APPLIANCES HAVING ELECTRICAL CONNECTIONS |
| NF EN ISO 228-1 : 2003 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
| NF ISO 619976 : 1997 | NATURAL GAS - CALCULATION OF CALORIFIC VALUES, DENSITY, RELATIVE DENSITY WOBBE INDEX FROM COMPOSITION |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| NF EN 88-1 : 2011 + A1 2016 | PRESSURE REGULATORS AND ASSOCIATED SAFETY DEVICES FOR GAS APPLIANCES - PART 1: PRESSURE REGULATORS FOR INLET PRESSURES UP TO AND INCLUDING 50 KPA |
| NF EN 437 : 2003 + A1 2009 | TEST GASES - TEST PRESSURES - APPLIANCE CATEGORIES |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
| NF EN 126 : 2012 | MULTIFUNCTIONAL CONTROLS FOR GAS BURNING APPLIANCES |
| NF EN 60529 : 92 AMD 2 2014 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) |
| NF EN 60335-1 : 2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS |
| CR 1404:1994 | Determination of emissions from appliances burning gaseous fuels during type-testing |
| NF EN 257 : 2011 | MECHANICAL THERMOSTATS FOR GAS-BURNING APPLIANCES |
| NF EN ISO 3166-1 : 2014 | CODES FOR THE REPRESENTATION OF NAMES OF COUNTRIES AND THEIR SUBDIVISION - PART 1: COUNTRY CODES |
| NF EN 60584-2 : 1993 | THERMOCOUPLES - PART 2: TOLERANCES |
| NF EN 10226-1 : 2004 | PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 1: TAPER EXTERNAL THREADS AND PARALLEL INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| NF EN 161 : 2011 + A3 2013 | AUTOMATIC SHUT-OFF VALVES FOR GAS BURNERS AND GAS APPLIANCES |
| NF EN 298 : 2012 | AUTOMATIC BURNER CONTROL SYSTEMS FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS |
| NF EN 10226-2 : 2005 | PIPE THREADS WHERE PRESSURE TIGHT JOINTS ARE MADE ON THE THREADS - PART 2: TAPER EXTERNAL THREADS AND TAPER INTERNAL THREADS - DIMENSIONS, TOLERANCES AND DESIGNATION |
| NF EN 60584-1 : 2014 | THERMOCOUPLES - PART 1: EMF SPECIFICATIONS AND TOLERANCES |
| 1990/396/EEC : 1990 | COUNCIL DIRECTIVE OF 29 JUNE 1990 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO APPLIANCES BURNING GASEOUS FUELS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.