PD 8010-2:2015+A1:2016
Current
The latest, up-to-date edition.
Pipeline systems Subsea pipelines. Code of practice
Hardcopy , PDF
English
30-11-2016
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Health, safety and assurance
5 Design - System and safety
6 Design - Mechanical integrity
7 Design - Landfalls, risers and tie-ins
8 Design - Materials and coatings
9 Design - Corrosion management
10 Construction - Fabrication and installation
11 Construction - Testing
12 Pre-commissioning and commissioning
13 Operation, maintenance and integrity assurance management
14 Abandonment
Annexes
Annex A (normative) - Quality assurance
Annex B (normative) - Records and document control
Annex C (informative) - Hazards in pipeline design
Annex D (normative) - Safety evaluation of pipelines
Annex E (normative) - Pipeline route selection
Annex F (normative) - Loads
Annex G (informative) - Buckling
Annex H (normative) - Environmental considerations
Bibliography
Defines recommendations for and guidance on the design, selection, specification and use of materials, construction, installation, testing, commissioning, operation, maintenance and abandonment of steel subsea pipelines in offshore, nearshore and landfall environments.
| Committee |
PSE/17/2
|
| DocumentType |
Standard
|
| ISBN |
978 0 580 94882 4
|
| Pages |
0
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
This part of PD 8010 gives recommendations for and guidance on the design, selection, specification and use of materials, construction, installation, testing, commissioning, operation, maintenance and abandonment of steel subsea pipelines in offshore, nearshore and landfall environments. Guidance on the use of flexible composite pipelines is also given.
It is not intended to replace or duplicate hydraulic, mechanical or structural design manuals.
This part of PD 8010 is applicable to subsea pipelines intended for the conveyance of hydrocarbon liquids, hydrocarbon gases, carbon dioxide and other gases, liquids and gases in two-phase flow, fluid-based slurries and water.
NOTE 1 Although primarily concerned with subsea pipelines associated with the oil and gas industry, PD 8010-2 is likely to have application to a wider range of offshore activities.
The extent of pipeline systems covered by this part of PD 8010 is shown in Figure 1. This part of PD 8010 is applicable to pipelines in water depths up to 500 m.
NOTE 2 In deeper water, other international codes such as DNV-OS-F101 are applicable.
| BS EN ISO 13628-15:2011 | Petroleum and natural gas industries. Design and operation of subsea production systems Subsea structures and manifolds |
| BS ISO 7005-1:2011 | Pipe flanges Steel flanges for industrial and general service piping systems |
| BS EN ISO 148-1:2016 | Metallic materials. Charpy pendulum impact test Test method |
| API STD 1104:2013 | WELDING OF PIPELINES AND RELATED FACILITIES |
| BS EN ISO 13628-2:2006 | Petroleum and natural gas industries. Design and operation of subsea production systems Unbonded flexible pipe systems for subsea and marine applications |
| ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| BS EN ISO 9004:2009 | Managing for the sustained success of an organization. A quality management approach |
| AWWA C205 : 2012 | CEMENT-MORTAR PROTECTIVE LINING AND COATING FOR STEEL WATER PIPE - 4 IN. (100 MM) AND LARGER - SHOP APPLIED |
| BS 4483:2005 | Steel fabric for the reinforcement of concrete. Specification |
| BS EN 10311:2005 | Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids |
| BS EN ISO 9001:2015 | Quality management systems. Requirements |
| ISO 15590-1:2009 | Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 1: Induction bends |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| PD 8010-5:2013 | Pipeline systems Subsea pipelines. Guide to operational practice |
| BS EN 1008:2002 | Mixing water for concrete. Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete |
| BS EN 12390-3:2009 | Testing hardened concrete Compressive strength of test specimens |
| BS 6374-3:1984 | Lining of equipment with polymeric materials for the process industries Specification for lining with stoved thermosetting resins |
| ASTM C 171 : 2016 : REDLINE | Standard Specification for Sheet Materials for Curing Concrete |
| NACE TM 02 84 : 2016 | EVALUATION OF PIPELINE AND PRESSURE VESSEL STEELS FOR RESISTANCE TO HYDROGEN-INDUCED CRACKING |
| API 5LC : 2015 | CRA LINE PIPE |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| API 6A : 2010 | SPECIFICATION FOR WELLHEAD AND CHRISTMAS TREE EQUIPMENT |
| ISO 14313:2007 | Petroleum and natural gas industries — Pipeline transportation systems — Pipeline valves |
| ASME B31.8 : 2016 | Gas Transmission and Distribution Piping Systems |
| ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
| BS EN ISO 15589-2:2014 | Petroleum, petrochemical and natural gas industries. Cathodic protection of pipeline transportation systems Offshore pipelines |
| BS EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials. Qualification based on tested welding consumables |
| NACE TM 01 77 : 2016 | LABORATORY TESTING OF METALS FOR RESISTANCE TO SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING IN H[2]S ENVIRONMENTS |
| BS EN 752:2008 | Drain and sewer systems outside buildings |
| ASME B31.3:2016 | PROCESS PIPING |
| BS 6374-4:1984 | Lining of equipment with polymeric materials for the process industries Specification for lining with cold curing thermosetting resins |
| BS ISO 10474:2013 | Steel and steel products. Inspection documents |
| BS EN 1992-1-1 : 2004 | EUROCODE 2: DESIGN OF CONCRETE STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| BS EN 12620:2013 | Aggregates for concrete |
| BS EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials. General rules |
| BS EN ISO 15653:2010 | Metallic materials. Method of test for the determination of quasistatic fracture toughness of welds |
| BS EN ISO 9606-1:2017 | Qualification testing of welders. Fusion welding Steels |
| BS EN 10224:2002 | Non-alloy steel tubes and fittings for the conveyance of water and other aqueous liquids. Technical delivery conditions |
| API SPEC 17J : 2014 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
| ASME B16.20 : 2012 | METALLIC GASKETS FOR PIPE FLANGES |
| API 2A : 1986 | RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS |
| BS EN ISO 3183 : 2012 | PETROLEUM AND NATURAL GAS INDUSTRIES - STEEL PIPE FOR PIPELINE TRANSPORTATION SYSTEMS |
| BS EN ISO 13628-5:2009 | Petroleum and natural gas industries. Design and operation of subsea production systems Subsea umbilicals |
| API 5L : 2012 | LINE PIPE |
| BS EN ISO 14001:2015 | Environmental management systems. Requirements with guidance for use |
| ISO 15590-3:2004 | Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 3: Flanges |
| BS EN 10244-2:2009 | Steel wire and wire products. Non-ferrous metallic coatings on steel wire Zinc or zinc alloy coatings |
| PD 8010-4:2012 | Pipeline systems Steel pipelines on land and subsea pipelines. Code of practice for integrity management |
| BS EN 13480-3:2017 | Metallic industrial piping Design and calculation |
| BS EN 197-1:2011 | Cement Composition, specifications and conformity criteria for common cements |
| NACE MR 01 75 : 2003 | METALS FOR SULFIDE STRESS CRACKING AND STRESS CORROSION CRACKING RESISTANCE IN SOUR OILFIELD ENVIRONMENTS |
| BS EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles. Specifications and test methods |
| BS ISO 1143:2010 | Metallic materials. Rotating bar bending fatigue testing |
| ISO 15590-2:2003 | Petroleum and natural gas industries Induction bends, fittings and flanges for pipeline transportation systems Part 2: Fittings |
| BS 6349-1-1:2013 | Maritime works General. Code of practice for planning and design for operations |
| BS EN 1991-1-4 : 2005 | EUROCODE 1: ACTIONS ON STRUCTURES - PART 1-4: GENERAL ACTIONS - WIND ACTIONS |
| API RP 17B : 2014 | RECOMMENDED PRACTICE FOR FLEXIBLE PIPE |
| MSS SP 44 : 2016 | STEEL PIPELINE FLANGES |
| BS 3518-3:1963 | Methods of fatigue testing Direct stress fatigue tests |
| BS 6349-1-4:2013 | Maritime works General. Code of practice for materials |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME B16.21 : 2016 | NONMETALLIC FLAT GASKETS FOR PIPE FLANGES |
| BS EN ISO 80000-1:2013 | Quantities and units General |
| ASME B16.9 : 2012 | FACTORY-MADE WROUGHT BUTTWELDING FITTINGS |
| BS EN 14161 : 2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - PIPELINE TRANSPORTATION SYSTEMS (ISO 13623:2009 MODIFIED) |
| BS 7371-12:2008 | Coatings on metal fasteners Requirements for imperial fasteners |
| AWWA C602 : 2017 | CEMENT-MORTAR LINING OF WATER PIPELINES IN PLACE - 4 INCH (100 MM) AND LARGER |
| BS PD8010-3(2009) : 2009 | PIPELINE SYSTEMS - PART 3: STEEL PIPELINES ON LAND - GUIDE TO THE APPLICATION OF PIPELINE RISK ASSESSMENT TO PROPOSED DEVELOPMENTS IN THE VICINITY OF MAJOR ACCIDENT HAZARD PIPELINES CONTAINING FLAMMABLES - SUPPLEMENT TO PD 8010-1:2004 |
| BS 3293:1960 | Specification for carbon steel pipe flanges (over 24 inches nominal size) for the petroleum industry |
| BS 4515-2:1999 | Specification for welding of steel pipelines on land and offshore Duplex stainless steel pipelines |
| BS ISO 12107:2003 | Metallic materials. Fatigue testing. Statistical planning and analysis of data |
| ASME B16.47 : 2017 | LARGE DIAMETER STEEL FLANGES: NPS 26 THROUGH NPS 60 METRIC/INCH STANDARD |
| API 17O : 2014 | SUBSEA HIGH INTEGRITY PRESSURE PROTECTION SYSTEMS (HIPPS) |
| BS EN ISO 9000:2015 | Quality management systems. Fundamentals and vocabulary |
| BS EN 12504-1:2009 | Testing concrete in structures Cored specimens. Taking, examining and testing in compression |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| BS EN 10204:2004 | Metallic products. Types of inspection documents |
| API 5LD : 2017 | CRA CLAD OR LINED STEEL PIPE |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.