PREN 1493 : DRAFT 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
VEHICLE LIFTS
01-12-2008
12-01-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
5.1 Preventing unauthorised operation
5.2 Control devices
5.3 Control positions
5.4 Duplicated drive systems
5.5 Speeds
5.6 Structural design of the supporting structure
5.7 Driving machinery
5.8 Load carrying devices
5.9 Additional requirements for lifts with balconies
5.10 Limiting the travel of the load carrying device
5.11 Unintended blocking of the load carrying device
5.12 Safety against rupture of mechanical bearing devices
5.13 Safety against leakage
5.14 Additional requirements for lifts with several drives
or lifting elements
5.15 Additional requirements for movable and mobile lifts
5.16 Protection against pinching and shearing
5.17 Safety devices
5.18 Protection against damage
5.19 Manually driven vehicle lifts
5.20 Electrical equipment
6 Verification of the safety requirements and/or measures
6.1 General
7 Information for use
7.1 General
7.2 Marking
7.3 Operation instructions
7.4 Name plate
Annex A (informative) - Structural calculations
A.1 Permissible stresses
Annex B (informative) - Examples of solutions
Annex C (normative) - Design of rope drives
Annex D (informative) - Example of information about wind
Annex E (normative) - Protection against leakage
Annex F (normative) - Additional requirements for cableless
controls and control systems
F.1 General
F.2 Control limitation
F.3 Stop
F.4 Serial data communication
F.5 Use of more than one operator control station
F.6 Battery-powered operator control stations
F.7 Receiver
F.8 Warnings
F.9 Information for use
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU Directive
98/37/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU Directive
2006/42/EC
Applies to stationary, mobile and movable vehicle lifts, which are not intended to lift persons but which are designed to raise vehicles totally, for the purpose of examining and working on or under the vehicles whilst in a raised position.
| Committee |
TC 98
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 08/30187719 DC : 0 | Identical |
| CEN Guide 414:2017 | Safety of machinery - Rules for the drafting and presentation of safety standards |
| ISO 4308-1:2003 | Cranes and lifting appliances Selection of wire ropes Part 1: General |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| EN 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.