PREN ISO 13849-2 : DRAFT 2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 2: VALIDATION
01-10-2012
12-01-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Validation process
5 Validation by analysis
6 Validation by testing
7 Validation of safety requirements specification
8 Validation of safety functions
9 Validation of performance levels and categories
10 Validation of environmental requirements
11 Validation of maintenance requirements
12 Validation of technical documentation and information
for use
Annex A (informative) - Validation tools for mechanical
systems
Annex B (informative) - Validation tools for pneumatic
systems
Annex C (informative) - Validation tools for hydraulic
systems
Annex D (informative) - Validation tools for electrical
systems
Annex E (informative) - Example of the validation of
fault behaviour and diagnostic means
Bibliography
Describes the procedures and conditions to be followed for the validation by analysis and testing of: - the safety functions provided; - the category achieved; and - the performance level achieved, of the safety-related parts of the control system (SRP/CS) in compliance with ISO 13849-1, using the design rationale provided by the designer.
| Committee |
TC 114
|
| DocumentType |
Draft
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| 10/30198892 DC : 0 | Identical |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| ISO 14119:2013 | Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
| ISO 4960:2007 | Cold-reduced carbon steel strip with a mass fraction of carbon over 0,25 % |
| ISO 11161:2007 | Safety of machinery — Integrated manufacturing systems — Basic requirements |
| EN 50205:2002 | Relays with forcibly guided (mechanically linked) contacts |
| ISO 5598:2008 | Fluid power systems and components Vocabulary |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| IEC 61078:2016 | Reliability block diagrams |
| ISO 14118:2000 | Safety of machinery Prevention of unexpected start-up |
| ISO 13851:2002 | Safety of machinery Two-hand control devices Functional aspects and design principles |
| IEC 61165:2006 | Application of Markov techniques |
| IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV | Low-voltage fuses - Part 1: General requirements |
| EN 952:1999 | Door leaves - General and local flatness - Measurement method |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.