SAE J 311 : 2000

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View superseded by

FLUID FOR PASSENGER CAR TYPE AUTOMATIC TRANSMISSIONS

Available format(s):

Superseded date: 22-02-2024

Language(s):

Published date: 01-01-2000

Publisher: SAE International

Abstract - (Show below) - (Hide below)

Gives the procedures and equipment used to measure critical characteristics of automatic transmission fluid (ATF) used in current automatic transmissions. It may help those concerned with the design of transmission components, and with the selection and marketing of automatic transmission fluids for use in passenger car and light-duty truck automatic transmissions. The information given will assist the understanding of terms relating to properties, designations and service applications of automatic transmission fluids.

General Product Information - (Show below) - (Hide below)

Document Type	Standard
ISBN
Pages
Published
Publisher	SAE International
Status	Superseded
Superseded By	SAE J311:2024

Standards Referenced By This Book - (Show below) - (Hide below)

MIL-HDBK-113 Revision C:1989	GUIDE FOR THE SELECTION OF LUBRICANTS, FUNCTIONAL FLUIDS, PRESERVATIVES AND SPECIALITY PRODUCTS FOR USE IN GROUND EQUIPMENT SYSTEMS
SAE J 2311 : 2015	AUTOMATIC TRANSMISSION HYDRAULIC PUMP TEST PROCEDURE
SAE J 1128 : 2015	LOW VOLTAGE PRIMARY CABLE
ISO 8092-2:2005	Road vehicles — Connections for on-board electrical wiring harnesses — Part 2: Definitions, test methods and general performance requirements
I.S. EN ISO 8092-2:2006	ROAD VEHICLES - CONNECTIONS FOR ON-BOARD ELECTRICAL WIRING HARNESSES - PART 2: DEFINITIONS, TEST METHODS AND GENERAL PERFORMANCE REQUIREMENTS
SAE J 2192 : 2016	RECOMMENDED TESTING METHODS FOR PHYSICAL PROTECTION OF WIRING HARNESSES
ASTM D 5363 : 2016 : REDLINE	Standard Specification for Anaerobic Single-Component Adhesives (AN)
ISO 15170-2:2001	Road vehicles — Four-pole electrical connectors with pins and twist lock — Part 2: Tests and requirements
SAE J 1678 : 2015	LOW VOLTAGE ULTRA THIN WALL PRIMARY CABLE
BS EN ISO 8092-2:2005	Road vehicles. Connections for on-board electrical wiring harnesses Definitions, test methods and general performance requirements
EN ISO 8092-2:2005	Road vehicles - Connections for on-board electrical wiring harnesses - Part 2: Definitions, test methods and general performance requirements (ISO 8092-2:2005)
98/711362 DC : DRAFT 98	ISO/DIS 5092-2 - ROAD VEHICLES - CONNECTIONS FOR ON ON-BOARD ELECTRICAL WIRING HARNESSES - PART 2: DEFINITIONS, TEST METHODS AND GENERAL PERFORMANCE REQUIREMENTS
SAE J 1127 : 2015	LOW VOLTAGE BATTERY CABLE

Standards Referencing This Book - (Show below) - (Hide below)

ASTM D 892 : 2013-07	TEST METHOD FOR FOAMING CHARACTERISTICS OF LUBRICATING OILS
ASTM D 4951 : 2014 : REDLINE	Standard Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry
ASTM D 665 : 2014-11	TEST METHOD FOR RUST-PREVENTING CHARACTERISTICS OF INHIBITED MINERAL OIL IN THE PRESENCE OF WATER
ASTM D 2882 : 2000	Standard Test Method for Indicating the Wear Characteristics of Petroleum and Non-Petroleum Hydraulic Fluids in Constant Volume Vane Pump (Withdrawn 2003)
ASTM D 808 : 2016 : REDLINE	Standard Test Method for Chlorine in New and Used Petroleum Products (High Pressure Decomposition Device Method)
SAE J 110 : 1997	SEALS - TESTING OF RADIAL LIP
ASTM D 1275 : 2015	Standard Test Method for Corrosive Sulfur in Electrical Insulating Liquids
MS9602 Revision B:1987	BRACKET ANGLE 90 DEG CRES ARM 5504 .190 X .312 BOLT

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart