02/124520 DC : DRAFT DEC 2002
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
EN 14598-3 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS
Superseded date
25-05-2005
Superseded by
Published date
23-11-2012
Publisher
Sorry this product is not available in your region.
EN 14598-3
| Committee |
PRI/42
|
| DocumentType |
Draft
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| EN ISO 62:2008 | Plastics - Determination of water absorption (ISO 62:2008) |
| IEC 60695-2-1:1991 | Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| EN ISO 10724-1:2001 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998) |
| EN ISO 6721-1:2011 | Plastics - Determination of dynamic mechanical properties - Part 1: General principles (ISO 6721-1:2011) |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| EN ISO 2818:1996 | Plastics - Preparation of test specimens by machining (ISO 2818:1994) |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN ISO 10352:2010 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area (ISO 10352:2010) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| ISO 11357-2:2013 | Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
| ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
| IEC 60167:1964 | Methods of test for the determination of the insulation resistance of solid insulating materials |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| ISO 1268-10:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens |
| ISO 1268-8:2004 | Fibre-reinforced plastics — Methods of producing test plates — Part 8: Compression moulding of SMC and BMC |
| IEC 60707:1999 | Flammability of solid non-metallic materials when exposed to flame sources - List of test methods |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| EN ISO 11667:1999 | Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of resin, reinforced-fibre and mineral-filler content - Dissolution methods (ISO 11667:1997) |
| EN ISO 2039-1:2003 | Plastics - Determination of hardness - Part 1: Ball indentation method (ISO 2039-1:2001) |
| EN ISO 12115:1997 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of flowability, maturation and shelf life (ISO 12115:1997) |
| EN ISO 295:2004 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| EN ISO 6603-2:2000 | Plastics - Determination of puncture impact behaviour of rigid plastics - Part 2: Instrumented puncture test (ISO 6603-2:2000) |
| EN ISO 10724-2:2000 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998) |
| EN ISO 1172:1998 | Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods (ISO 1172:1996) |
| EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| EN ISO 12114:1997 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of cure characteristics (ISO 12114:1997) |
| ISO 1268-11:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates |
| EN ISO 175:2010 | Plastics - Methods of test for the determination of the effects of immersion in liquid chemicals (ISO 175:2010) |
| ISO 10351:1992 | Plastics Determination of the combustibility of specimens using a 125 mm flame source |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.