Skip to content
Please enter a keyword to search

  • 15/30259978 DC : 0

    NA Status of Standard is Unknown

    BS EN 62477-2 - SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 2: POWER ELECTRONIC CONVERTERS FROM 1000 V A.C. OR 1500 V D.C. UP TO 36 KV A.C. OR 54 KV D.C.

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date: 

    Publisher:  British Standards Institution

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    FOREWORD
    INTRODUCTION
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Protection against hazards
    5 Test requirements
    6 Information and marking requirements
    7 Internal Arc Classification Requirements
    Annex A (normative) - Additional information for protection
            against electric shock
    Annex B (informative) - Considerations for the reduction of
            the pollution degree
    Annex C (informative) - Symbols referred to in IEC 62477-1
    Annex D (normative) - Evaluation of clearance and creepage
            distances
    Annex E (informative) - Altitude correction for clearances
    Annex F (normative) - Clearance and creepage distance
            determination for frequencies greater than 30 kHz
    Annex G (informative) - Cross-sections of round conductors
    Annex H (informative) - Guidelines for RCD compatibility
    Annex I (informative) - Examples of overvoltage category
            reduction
    Annex J (informative) - Burn thresholds for touchable
            surfaces
    Annex K (informative) - Table of electrochemical potentials
    Annex L (informative) - Measuring instrument for touch
            current measurements
    Annex M (informative) - Test probes for determining access
    Annex N (normative) - Arc fault test and labelling
            requirements
    Bibliography

    General Product Information - (Show below) - (Hide below)

    Comment Closes On
    Committee PEL/22
    Document Type Draft
    Publisher British Standards Institution
    Status NA

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
    IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV Information technology equipment - Safety - Part 1: General requirements
    IEC 62423:2009 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses
    IEC 61936-1:2010+AMD1:2014 CSV Power installations exceeding 1 kV a.c. - Part 1: Common rules
    IEC 60947-7-2:2009 Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors
    IEC 62271-200:2011 High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
    IEC 62271-201:2014 High-voltage switchgear and controlgear - Part 201: AC solid-insulation enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV
    IEC 60073:2002 Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators
    IEC TS 61201:2007 Use of conventional touch voltage limits - Application guide
    IEC 61643-12:2008 Low-voltage surge protective devices - Part 12: Surge protective devices connected to low-voltage power distribution systems - Selection and application principles
    IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
    IEC 61558-2-16:2009+AMD1:2013 CSV Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units
    IEC 60947-7-1:2009 Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper conductors
    IEC 61082-1:2014 RLV Preparation of documents used in electrotechnology - Part 1: Rules
    IEC 60085:2007 Electrical insulation - Thermal evaluation and designation
    IEC 61558-1:2017 Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests
    NFPA 70E : 2018 ELECTRICAL SAFETY IN THE WORKPLACE
    IEC 62079:2001 Preparation of instructions - Structuring, content and presentation
    IEC 60664-5:2007 Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm
    IEC 60071-2:1996 Insulation co-ordination - Part 2: Application guide
    IEEE 1584 : 2002 GUIDE FOR PERFORMING ARC-FLASH HAZARD CALCULATIONS
    IEC 62477-1:2012+AMD1:2016 CSV Safety requirements for power electronic converter systems and equipment - Part 1: General
    IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
    IEC 60071-1:2006+AMD1:2010 CSV Insulation co-ordination - Part 1: Definitions, principles and rules
    IEC 60695-11-5 : 2.0 FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE
    IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements
    IEC TR 60479-5:2007 Effects of current on human beings and livestock - Part 5: Touch voltage threshold values for physiological effects
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective