ASTM D 115 : 2017 : REDLINE
Current
The latest, up-to-date edition.
Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation
English
14-11-2017
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 10.01, 2017 Defines tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment.
| Committee |
D 09
|
| DevelopmentNote |
Supersedes ASTM D 1346 (12/2001)
|
| DocumentType |
Redline
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
1.1These test methods cover tests for solvent containing varnishes primarily intended to provide electrical, mechanical, and chemical protection for electrical equipment. These test methods include tests for control and performance as follows:
| Procedure | Section |
| Build | 38 – 42 |
| Dielectric Strength | 43 – 48 |
| Drainage | 26 – 32 |
| Flash Point | 18 – 20 |
| Nonvolatile Matter | 21 – 25 |
| Oil Resistance | 54 – 56 |
| Preparation of Test Specimens | 7 |
| Specific Gravity | 9 – 12 |
| Temperature Index | 49 – 50 |
| Time of Drying | 33 – 37 |
| Varnish Compatibility | 51 – 53 |
| Viscosity | 13 – 17 |
1.2Where the entire test method is included in this standard, the precision and bias are not known unless given in the stated method.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 5.
Note 1:There is no equivalent IEC standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
| ASTM D 1304 : 1999 | Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation |
| ASTM D 3089 : 1997 : R2008 | Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes |
| ASTM D 3955 : 2013 : REDLINE | Standard Specification for Electrical Insulating Varnishes |
| TAPPI T 666 : OM 86 | VISCOSITY OF ADHESIVES USING A LOW-SHEAR ROTATING APPARATUS |
| ASTM D 2519 : 2007 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 2756 : 2007 : R2012 | Standard Test Method for Weight Loss of Electrical Insulating Varnishes |
| MIL-C-47221 Revision A:1982 | COMPOUND, MOLDING, EPOXY RESIN, SILICON DIOXIDE AND ASBESTOS FIBER FILL |
| ASTM D 2756 : 2007 | Standard Test Method for Weight Loss of Electrical Insulating Varnishes |
| DIN 65065:1979-08 | AEROSPACE; RESINS FOR FIBER REINFORCED, TECHNICAL SPECIFICATION |
| ASTM D 1304 : 1999 : R2005 | Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation |
| ASTM D 1084 : 2016 : REDLINE | Standard Test Methods for Viscosity of Adhesives |
| ASTM D 2519 : 2007 : R2012 | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test |
| ASTM D 2832 : 1992 : R2016 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 3251 : 2004 : R2009 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| NEMA RE 2:1999 | Electrical Insulating Varnish |
| ASTM D 7230 : 2006 : R2013 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| ASTM D 1304 : 1999 : R2012 | Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation |
| ASTM D 4209 : 2007 | Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes |
| ASTM D 3251 : 2004 : R2013 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| MIL-E-22118 Revision B:1974 | ENAMEL, ELECTRICAL INSULATING |
| MIL-C-47002 Revision A:1991 | COATING, POLYURETHANE, SINGLE COMPONENT SYSTEM |
| MIL-C-47200 Base Document:1974 | WIRE AND CABLE, ELECTRICAL, SINGLE CONDUCTOR, TWISTED PAIRS AND MULTICONDUCTOR SHIELDED AND JACKETED, HIGH TEMPERATURE |
| ASTM D 4882 : 2017 : REDLINE | Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Twisted-Coil Test |
| ASTM D 2832 : 1992 : R1999 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 7230 : 2006 | Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates |
| GOST 849:2018 | Primary nickel. SpecificationsE |
| MIL-I-24092 Revision D:1993 | INSULATING VARNISHES AND SOLVENTLESS RESINS FOR APPLICATION BY THE DIP PROCESS |
| ASTM D 2832 : 1992 : R2005 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| MIL-P-16406 Revision A:1974 | PAINT, BLACK, HIGH GLOSS, QUICK DRYING |
| ASTM D 2756 : 2007 : R2017 | Standard Test Method for Weight Loss of Electrical Insulating Varnishes |
| ASTM D 4209 : 2007 : R2013 | Standard Practice for Determining Volatile and Nonvolatile Content of Cellulosics, Emulsions, Resin Solutions, Shellac, and Varnishes |
| ASTM D 3251 : 2004 | Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire |
| ASTM D 2832 : 1992 : R2011 | Standard Guide for Determining Volatile and Nonvolatile Content of Paint and Related Coatings |
| ASTM D 295 : 2012 | Standard Test Methods for Varnished Cotton Fabrics Used for Electrical Insulation (Withdrawn 2020) |
| ASTM D 580 : 2004 | Standard Specification for Greige Woven Glass Tapes and Webbings |
| ASTM D 202 : 2017 : REDLINE | Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| ASTM E 104 : 2002 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions |
| ASTM D 1475 : 2013 : REDLINE | Standard Test Method For Density of Liquid Coatings, Inks, and Related Products |
| ASTM D 374 : 1999 | Standard Test Methods for Thickness of Solid Electrical Insulation |
| ASTM D 5423 : 2014 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.