ASTM D 1434 : 1982 : R2015 : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
Hardcopy , PDF
26-06-2023
English
23-09-2015
Important note : Users cannot be edited or removed once added to your Multi user PDF.CONTAINED IN VOL. 15.09, 2015 Specifies the estimation of the steady-state rate of transmission of a gas through plastics in the form of film, sheeting, laminates, and plastic-coated papers or fabrics.
| Committee |
F 02
|
| DocumentType |
Test Method
|
| Pages |
13
|
| ProductNote |
Reconfirmed EDT 1
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the estimation of the steady-state rate of transmission of a gas through plastics in the form of film, sheeting, laminates, and plastic-coated papers or fabrics. This test method provides for the determination of (1) gas transmission rate (GTR), (2) permeance, and, in the case of homogeneous materials, (3) permeability.
1.2Two procedures are provided:
1.2.1Procedure M—Manometric.
1.2.2Procedure V—Volumetric.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 1307 : 2020 | Standard Test Method for Oxygen Transmission Rate Through Dry Packages Using a Coulometric Sensor |
| ASTM D 5886 : 1995 : R2023 | Standard Guide for Selection of Test Methods to Determine Rate of Fluid Permeation Through Geomembranes for Specific Applications |
| ASTM F 641 : 2009 : R2023 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
| ASTM D 2673 : 2014 : R2022 | Standard Specification for Oriented Polypropylene Film |
| ASTM C 1484 : 2010 : R2018 | Standard Specification for Vacuum Insulation Panels |
| ASTM F 2097 : 2020 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM E 2662 : 2015 : R2022 | Standard Practice for Radiographic Examination of Flat Panel Composites and Sandwich Core Materials Used in Aerospace Applications |
| ASTM D 7407 : 2007 : R2020 | Standard Guide for Determining the Transmission of Gases Through Geomembranes |
| ASTM D 4000 : 2023 | Standard Classification System for Specifying Plastic Materials |
| ASTM E 2662 : 2015 | Standard Practice for Radiographic Examination of Flat Panel Composites and Sandwich Core Materials Used in Aerospace Applications |
| ASTM D 3664 : 2016 | Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment (Withdrawn 2022) |
| ASTM D 3985 : 2017 | Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor |
| ASTM D 6338 : 2017 | Standard Classification System for Highly Crosslinked Thermoplastic Vulcanizates (HCTPV) Based on ASTM Standard Test Methods |
| ASTM D 4000 : 2016 | Standard Classification System for Specifying Plastic Materials |
| ASTM F 624 : 2009 : R2015 : EDT 1 | Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications |
| ASTM F 2097 : 2016 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM D 7407 : 2007 : R2012 | Standard Guide for Determining The Transmission of Gases Through Geomembranes |
| ASTM D 6455 : 2011 : R2018 | Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs) |
| ASTM D 7106/D7106M : 2005 : R2015 : EDT 1 | Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes |
| ASTM F 641 : 2009 : R2014 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
| ASTM D 5886 : 1995 : R2018 | Standard Guide for Selection of Test Methods to Determine Rate of Fluid Permeation Through Geomembranes for Specific Applications |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM F 602 : 2009 : R2015 | Standard Criteria for Implantable Thermoset Epoxy Plastics (Withdrawn 2024) |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM F 1307 : 2014 | Standard Test Method for Oxygen Transmission Rate Through Dry Packages Using a Coulometric Sensor |
| ASTM D 2673 : 2014 | Standard Specification for Oriented Polypropylene Film |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 1898 : 1968 : R1989 | Standard Practice for Sampling of Plastics (Withdrawn 1998) |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.