ASTM D 3288/D3288M : 2020
Current
The latest, up-to-date edition.
Standard Test Methods for Magnet-Wire Enamels
Hardcopy , PDF
English
01-09-2020
Committee |
D 09
|
DocumentType |
Test Method
|
Pages |
7
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1These test methods cover testing liquid enamel coatings used to produce film-insulated magnet wire.
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined
1.3The test methods appear as follows:
Sections | |
Density | 6 – 10 |
Determined Solids | 16 – 22 |
Effective Solids | 31 – 37 |
Flash Point | 11 – 15 |
Infrared Analysis | 45 – 50 |
Stack Loss | 23 – 30 |
Viscosity | 38 – 44 |
1.4There is no known IEC equivalent document.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 476 : 2015 : R2021 | Standard Classification for Dry Pigmentary Titanium Dioxide Products |
ASTM E 131 : 2010 : R2023 | Standard Terminology Relating to Molecular Spectroscopy |
ASTM D 5423 : 2022 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
ASTM D 1298 : 2012 : REV B : R2017 : EDT 1 | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM E 168 : 2016 : R2023 | Standard Practices for General Techniques of Infrared Quantitative Analysis |
ASTM D 1298 : 2012 : REV B : R2017 | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
ASTM D 1711 : 2011 | Standard Terminology Relating to Electrical Insulation |
ASTM E 691 : 2020 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 1711 : 2024 : REV A | Standard Terminology Relating to Electrical Insulation |
ASTM E 691 : 2019 : EDT 1 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 691 : 2023 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 5423 : 2023 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
ASTM D 56 : 2021 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
ASTM E 131 : 2010 : R2015 | Standard Terminology Relating to Molecular Spectroscopy |
ASTM E 691 : 2022 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 56 : 2016 : REV A | Standard Test Method for Flash Point by Tag Closed Cup Tester |
ASTM E 691 : 2009 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM E 2975 : 2023 | Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers |
ASTM D 56 : 2021 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
ASTM E 691 : 2021 | Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method |
ASTM D 1711 : 2024 | Standard Terminology Relating to Electrical Insulation |
ASTM D 476 : 2015 | Standard Classification for Dry Pigmentary Titanium Dioxide Products |
ASTM D 1711 : 2022 | Standard Terminology Relating to Electrical Insulation |
ASTM D 1711 : 2020 | Standard Terminology Relating to Electrical Insulation |
ASTM D 56 : 2022 | Standard Test Method for Flash Point by Tag Closed Cup Tester |
ASTM D 56 : 1987 | Standard Test Method for Flash Point by Tag Closed Tester |
ASTM E 2975 : 2024 | Standard Test Method for Calibration or Calibration Verification of Constant Speed Concentric Cylinder Rotational Viscometers |
ASTM D 5423 : 2014 | Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation |
ASTM E 2975 : 2016 : EDT 1 | Standard Test Method for Calibration or Calibration Verification of Concentric Cylinder Rotational Viscometers |
ASTM E 168 : 2016 | Standard Practices for General Techniques of Infrared Quantitative Analysis |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.