BS EN 13600:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Copper and copper alloys. Seamless copper tubes for electrical purposes
Hardcopy , PDF
21-04-2021
English
31-07-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Designations
5 Ordering information
6 Requirements
7 Sampling
8 Test methods
9 Declaration of conformity and inspection documentation
10 Marking, packaging, labelling
Annex A (informative) - Characteristics of coppers for
electrical purposes
Bibliography
Describes the composition, property requirements, including electrical properties, and tolerances on dimensions and form for seamless drawn copper tubes for electrical purposes.
Committee |
NFE/34
|
DevelopmentNote |
Supersedes BS 1977(1976) and 99/710680 DC (10/2002) Supersedes 11/30240453 DC. (07/2013)
|
DocumentType |
Standard
|
Pages |
30
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for seamless drawn copper tubes for electrical purposes, delivered in straight lengths or alternatively in level wound coils with the cross-sections and size ranges below: - for round tubes in straight lengths with outside diameters from 3 mm up to and including 450 mm and wall thicknesses from 0,3 mm; - for round tubes in level wound coils with outside diameters from 3 mm up to and including 30 mm and wall thicknesses from 0,3 mm; - for square and rectangular tubes with major outside dimension from 5 mm up to and including 150 mm and wall thicknesses from 0,5 mm up to and including 10 mm. The sampling procedures and test methods for verification of conformity to the requirements of this standard are also specified.
Standards | Relationship |
NF EN 13600 : 2013 | Identical |
SN EN 13600 : 2013 | Identical |
UNE-EN 13600:2014 | Identical |
NS EN 13600 : 2013 | Identical |
I.S. EN 13600:2013 | Identical |
DIN EN 13600:2013-09 | Identical |
NEN EN 13600 : 2013 | Identical |
NBN EN 13600 : 2013 | Identical |
EN 13600:2013 | Identical |
UNI EN 13600 : 2013 | Identical |
ONORM EN 13600 : 2013 | Identical |
ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
EN 1655:1997 | Copper and copper alloys - Declarations of conformity |
EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
ISO 197-1:1983 | Copper and copper alloys — Terms and definitions — Part 1: Materials |
EN 1412:2016 | Copper and copper alloys - European numbering system |
ISO 1190-1:1982 | Copper and copper alloys — Code of designation — Part 1: Designation of materials |
EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
ISO 8491:1998 | Metallic materials Tube (in full section) Bend test |
EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
ISO 1811-2:1988 | Copper and copper alloys — Selection and preparation of samples for chemical analysis — Part 2: Sampling of wrought products and castings |
ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
EN ISO 2626:1995 | Copper - Hydrogen embrittlement test (ISO 2626:1973) |
EN 1976:2012 | Copper and copper alloys - Cast unwrought copper products |
EN 12449:2016 | Copper and copper alloys - Seamless, round tubes for general purposes |
EN 1173:2008 | Copper and copper alloys - Material condition designation |
ISO 7438:2016 | Metallic materials Bend test |
EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
EN 10204:2004 | Metallic products - Types of inspection documents |
ISO 80000-1:2009 | Quantities and units — Part 1: General |
ISO 9001:2015 | Quality management systems — Requirements |
EN ISO 8491:2004 | Metallic materials - Tube (in full section) - Bend test (ISO 8491:1998) |
ISO 2626:1973 | Copper — Hydrogen embrittlement test |
EN 50149:2012 | Railway applications - Fixed installations - Electric traction - Copper and copper alloy grooved contact wires |
EN ISO 7438:2016 | Metallic materials - Bend test (ISO 7438:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.