• Shopping Cart
    There are no items in your cart

BS EN 15266:2007

Current

Current

The latest, up-to-date edition.

Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

30-04-2008

€303.84
Excluding VAT

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Design requirements
  4.1 General
  4.2 Materials
  4.3 Nominal size DN and pressure drop
  4.4 Threads
  4.5 PLT fittings
  4.6 Seals and sealing agents
  4.7 Environment
  4.8 Supports
  4.9 Electrical conductivity requirements
  4.10 Cover
5 Performance and test requirements
  5.1 General
  5.2 Tightness
  5.3 Dimensional check
  5.4 Bending performance
  5.5 Crushing resistance
  5.6 Stability under pressure
  5.7 Wear resistance of outer cover
  5.8 Structural strength test
  5.9 Impact resistance
  5.10 Penetration resistance
  5.11 Resistance to pull out
  5.12 Chemical resistance
  5.13 Low temperature resistance
  5.14 Ageing
  5.15 Tightness in case of fire
  5.16 Reaction to fire
  5.17 Electrical conductivity
  5.18 Pressure drop
  5.19 Maximum load for admissible deformation of PLT
       support
  5.20 Dangerous substances
6 Evaluation of conformity
  6.1 General
  6.2 Type testing
  6.3 Factory production control (FPC)
  6.4 Assembly and installation instruction
  6.5 Marking, labelling and packaging
Annex A (normative) Single-flame source test
  A.1 General
  A.2 Standardised mounting and fixing
  A.3 Test definition
  A.4 Test duration
Annex B (normative) Thermal attack by a single burning
        item
  B.1 General
  B.2 Standardised mounting and fixing
Annex ZA (informative) Clauses of this European Standard
         addressing the provisions of the EU Construction
         Products Directive (89/106/EEC)
  ZA.1 Scope and relevant characteristics
  ZA.2 Procedure for attestation of conformity of stainless
       steel pliable corrugated gas tubing kits
       ZA.2.2 EC Certificate and declaration of conformity
  ZA.3 CE marking and labeling
Bibliography

Describes the requirements for material, design, manufacture, testing, marking and documentation of stainless steel pliable corrugated gas tubing kits for buildings with a maximum operating pressure (MOP) less than or equal to 0,5 bar and a nominal size range from DN 10 to DN 50.

Committee
GSE/42
DevelopmentNote
Supersedes 05/30135337 DC. (06/2007) Partially supersedes BS 7838(1996). (04/2008)
DocumentType
Standard
Pages
56
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
NEN EN 15266 : 2007 Identical
I.S. EN 15266:2007 Identical
NF EN 15266 : 2007 Identical
EN 15266:2007 Identical
UNI EN 15266 : 2007 Identical
NS EN 15266 : 1ED 2007 Identical
DIN EN 15266:2007-08 Identical
SN EN 15266 : 2007 Identical
NBN EN 15266 : 2007 Identical

13/30199128 DC : 0 BS 6891 - SPECIFICATION FOR THE INSTALLATION AND MAINTENANCE OF LOW PRESSURE GAS INSTALLATION PIPEWORK OF UP TO 35 MM (R1[1/4]) IN PREMISES
BS 6173:2009 Specification for installation and maintenance of gas-fired catering appliances for use in all types of catering establishments (2nd and 3rd family gases)
BS 6172(2010) : 2010 SPECIFICATION FOR INSTALLATION, SERVICING AND MAINTENANCE OF DOMESTIC GAS COOKING APPLIANCES (2ND AND 3RD FAMILY GASES)
BS 6891:2015 Specification for the installation and maintenance of low pressure gas installation pipework of up to 35 mm (R1¼) on premises
PD 54823:2016 Guidance for the design, commissioning and maintenance of LPG systems in small craft
15/30281782 DC : 0 PD 5482-3 - GUIDANCE FOR THE DESIGN, COMMISSIONING AND MAINTENANCE OF LPG SYSTEMS IN SMALL CRAFT

EN 1775:2007 Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations
89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 751-2:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds
ISO 11925-2:2010 Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test
EN ISO 9227:2017 Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017)
EN 13823:2010+A1:2014 Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item
EN 10028-7:2016 Flat products made of steels for pressure purposes - Part 7: Stainless steels
EN ISO 10380:2012 Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2012)
ISO 10380:2012 Pipework — Corrugated metal hoses and hose assemblies
EN 437:2003+A1:2009 Test gases - Test pressures - Appliance categories
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 6509:1981 Corrosion of metals and alloys Determination of dezincification resistance of brass
ISO 9001:2015 Quality management systems — Requirements
EN 751-1:1996 Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
EN 1363-1:2012 Fire resistance tests - Part 1: General Requirements
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
EN 549:1994 Rubber materials for seals and diaphragms for gas appliances and gas equipment
ISO 7369:2004 Pipework Metal hoses and hose assemblies Vocabulary
EN ISO 6509:1995 Corrosion of metals and alloys - Determination of dezincification resistance of brass (ISO 6509:1981)
EN 12165:2016 Copper and copper alloys - Wrought and unwrought forging stock
EN 10226-1:2004 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation
ISO 6957:1988 Copper alloys Ammonia test for stress corrosion resistance
EN ISO 7369:2004 Pipework - Metal hoses and hose assemblies - Vocabulary (ISO 7369:2004)
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.