BS EN 60317-0-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Specifications for particular types of winding wires General requirements. Enamelled round copper wire
Hardcopy
16-12-2019
English
31-01-2014
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions, general notes and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation (nominal conductor diameters
up to and including 1,600 mm)
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Annex A (informative) - Dimensions for intermediate nominal
conductor diameters (R 40)
Annex B (informative) - Method for the calculation of linear
resistance
Annex C (informative) - Resistance
Bibliography
Annex ZA (normative) - Normative references to international
Publications with their corresponding
European publications
Defines general requirements of enamelled round copper winding wires with or without bonding layer.
Committee |
W/-
|
DevelopmentNote |
Renumbers and supersedes BS 6811-3.0(1993). 1996 version incorporates amendment 8984 to BS 6811-3.0(1993). (10/2005) Supersedes 03/310543 DC (05/2006) Supersedes 05/30143859 DC. (10/2008) Supersedes 11/30251799 DC. (01/2014)
|
DocumentType |
Standard
|
Pages |
38
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
IEC 60317-0-1:2013 specifies general requirements of enamelled round copper winding wires with or without bonding layer. The range of nominal conductor diameters is given in the relevant specification sheet. This fourth edition cancels and replaces the third edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- revision to the definition of nominal conductor dimension;
- new subclause containing general notes on winding wire, formerly a part of the scope;
- revision to elongation requirements in Table 4;
- revisions to Clause 13, Breakdown voltage, to include new requirements for intermediate wire diameters;
- revision to continuity of insulation requirements in Table 13;
- revision to the introduction of Annex A;
- revision to B.2 of Annex B;
- revision to Table C.1 of Annex C. Keywords: requirements of enamelled round copper winding wires
This publication is to be read in conjunction with the IEC 60851 series.
Standards | Relationship |
UNE-EN 60317-0-1:2008 | Identical |
SN EN 60317-0-1 : 1998 AMD 2 2005 | Identical |
IEC 60317-0-1:2013 | Identical |
I.S. EN 60317-0-1:2014 | Identical |
DIN EN 60317-0-1:2014-09 | Identical |
EN 60317-0-1:2014 | Identical |
NF EN 60317-0-1 : 2014 | Identical |
BS EN 60317-7:1995 | Specifications for particular types of winding wires Polyimide enamelled round copper wire, class 220 |
ISO 3:1973 | Preferred numbers Series of preferred numbers |
IEC 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
EN 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.