• Shopping Cart
    There are no items in your cart

BS EN 877 : 1999

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE

Available format(s)

Hardcopy , PDF

Superseded date

04-11-2021

Superseded by

BS EN 877:2021

Language(s)

English

Published date

01-01-2006

€303.84
Excluding VAT

Foreword
1 Scope
2 Normative references
3 Definitions
4 Technical requirements
  4.1 General
  4.2 Dimensions
  4.3 Interconnection
  4.4 Mass
  4.5 Material characteristics of pipes, fittings
       and accessories
  4.6 Coatings for pipes, fittings and accessories
  4.7 Joints
  4.8 Buried systems
  4.9 Rainwater systems installed outside buildings
  4.10 Marking
5 Test methods
  5.1 Surface condition
  5.2 Dimensions
  5.3 Mass
  5.4 Tensile strength of pipes and fittings
  5.5 Brinell hardness
  5.6 Ring crush test for grey cast iron pipes
  5.7 Coatings
  5.8 Joints
  5.9 Buried systems
  5.10 Rainwater systems installed outside buildings
  5.11 Marking
6 Evaluation of conformity
Annex A (informative) - Other dimensions for buried
        systems
Annex B (informative) - Other dimensions for rainwater
        systems to be installed outside buildings
Annex C (informative) - Field of use for buried pipes and
        fittings, characteristics of soils, load-bearing
        capacity
Annex D (normative) - Evaluation of conformity
Annex E (informative) - Surveillance by an accredited third
        party (certification by third party)
Annex F (informative) - General information on some product
        characteristics
Annex G (informative) - Method of calculation of gross
        calorific potential of external coatings for
        the range, noted PCS[range ext.coating]
Annex H (normative) - Reaction to fire test (SBI adaptation
        for testing a products range)
Annex ZA (informative) - Clauses of the European Standard
         addressing essential requirements or other
         provisions of EU Directives
Bibliography
National Annex NA (informative) - National annex

Defines cast iron pipeline components used for the construction of discharge systems for drains and building normally as gravity systems. The range is from DN 40 to DN 600 inclusive. Covers requirements for the dimensions and tolerances, appearance, materials, mechanical properties, standard coatings for cast iron pipes, fittings and accessories.

Committee
PSE/10
DevelopmentNote
Supersedes 92/83373 DC, BS 416-2(1990) and BS 6087(1990). (09/2005) Supersedes 02/710117 DC. (11/2006)
DocumentType
Standard
Pages
66
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

07/30138205 DC : DRAFT MAR 2007 BS 6297 - DESIGN AND INSTALLATION OF SMALL SEWAGE TREATMENT WORKS AND CESSPOOLS - CODE OF PRACTICE
BS 6297(2007) : 2007 CODE OF PRACTICE FOR THE DESIGN AND INSTALLATION OF DRAINAGE FIELDS FOR USE IN WASTEWATER TREATMENT
BS 437:2008 Specification for cast iron drain pipes, fittings and their joints for socketed and socketless systems
08/30156969 DC : DRAFT JAN 2008 BS 437 - SPECIFICATION FOR CAST IRON DRAIN PIPES, FITTINGS AND THEIR JOINTS FOR SOCKETED AND SOCKETLESS SYSTEMS

ISO 1514:2016 Paints and varnishes — Standard panels for testing
ISO 7724-1:1984 Paints and varnishes Colorimetry Part 1: Principles
EN 10002-1 : 2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
EN 605 : 1992 PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING
ISO 1716:2010 Reaction to fire tests for products Determination of the gross heat of combustion (calorific value)
EN 20898-1 : 1991 MECHANICAL PROPERTIES OF FASTENERS - BOLTS, SCREWS AND STUDS
EN 598:2007+A1:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
ISO 2808:2007 Paints and varnishes Determination of film thickness
EN 10088-3:2014 Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
EN 45011:1998 General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996)
ISO 7724-2:1984 Paints and varnishes Colorimetry Part 2: Colour measurement
ISO 11925-2:2010 Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test
EN ISO 2409:2013 Paints and varnishes - Cross-cut test (ISO 2409:2013)
EN ISO 9002:1994/AC:1997 QUALITY SYSTEMS - SPECIFICATION FOR PRODUCTION AND INSTALLATION
ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
EN 10088-2:2014 Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes
EN 45011 : 1998 GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS
ISO/IEC 17011:2004 Conformity assessment General requirements for accreditation bodies accrediting conformity assessment bodies
EN 13823:2010+A1:2014 Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item
ISO 9002:1994 Quality systems — Model for quality assurance in production, installation and servicing
EN ISO 6708:1995 Pipework components - Definition and selection of DN (nominal size) (ISO 6708:1995)
ISO 4628-3:2016 Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting
ISO 7253:1996 Paints and varnishes — Determination of resistance to neutral salt spray (fog)
EN 476:2011 General requirements for components used in drains and sewers
ISO 7724-3:1984 Paints and varnishes Colorimetry Part 3: Calculation of colour differences
EN 1366-3:2009 Fire resistance tests for service installations - Part 3: Penetration seals
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
EN 10204:2004 Metallic products - Types of inspection documents
ISO 9001:2015 Quality management systems — Requirements
ISO 2812-1:2017 Paints and varnishes — Determination of resistance to liquids — Part 1: Immersion in liquids other than water
EN 14366:2004 Laboratory measurement of noise from waste water installations
ISO 185:2005 Grey cast irons Classification
EN 10003-1 : 1994 METALLIC MATERIALS - BRINELL HARDNESS TEST - TEST METHOD
PREN 1366-3 : DRAFT 1993 FIRE TESTS FOR BUILDING ELEMENTS AND COMPONENTS - FIRE RESISTANCE TESTING OF SERVICE INSTALLATIONS - PART 3: PENETRATION SEALS
ISO 2409:2013 Paints and varnishes Cross-cut test
EN ISO 1716:2010 Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010)
ISO 4633:2015 Rubber seals — Joint rings for water supply, drainage and sewerage pipelines — Specification for materials
ISO 4628-2:2016 Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
EN 10088-1:2014 Stainless steels - Part 1: List of stainless steels

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.