BS EN ISO 15493 : 2003
Current
The latest, up-to-date edition.
PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS), UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) AND CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM - METRIC SERIES (ISO 15493:2003)
Hardcopy , PDF
English
01-01-2003
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Material
6 General characteristics
7 Geometrical characteristics
8 Mechanical characteristics
9 Physical characteristics
10 Chemical characteristics
11 Adhesives
12 Performance requirements
13 Classification of components
14 Design of a thermoplastics piping system for
industrial applications
15 Installation of piping systems
16 Declaration of compliance
17 Marking
Annex A (normative) Specific characteristics and
requirements for industrial piping systems made
from acrylonitrile-butadiene-styrene (ABS)
Annex B (normative) Specific characteristics and
requirements for industrial piping systems made
from unplasticized poly(vinyl chloride) (PVC-U)
Annex C (normative) Specific characteristics and requirements
for industrial piping systems made from chlorinated
poly(vinyl chloride) (PVC-C)
Bibliography
Annex ZA (normative) - Normative references to
international publications with their relevant
European publications
Annex ZB (informative) - Clauses of this Standard
addressing essential requirements or other
provisions of EU Directives
Defines the characteristics and requirements for components such as pipes, fittings and valves made from one of the following materials: 1. Acrylonitrile-butadiene-styrene (ABS); 2. Unplasticized poly(vinyl chloride) (PVC-U); 3. Chlorinated poly(vinyl chloride) (PVC-C).
Committee |
PRI/88/2
|
DevelopmentNote |
Supersedes 16/30327064 DC. 2003 Edition Re-issued in February 2017 & incorporates AMD 1 2017. (02/2017)
|
DocumentType |
Standard
|
Pages |
74
|
PublisherName |
British Standards Institution
|
Status |
Current
|
Supersedes |
Standards | Relationship |
NS EN ISO 15493 : 2003 AMD 1 2017 | Identical |
NF EN ISO 15493 : 2004 AMD 1 2017 | Identical |
I.S. EN ISO 15493:2003 | Identical |
SN EN ISO 15493 : 2003 AMD 1 2017 | Identical |
NEN EN ISO 15493 : 2003 AMD 1 2017 | Identical |
UNI EN ISO 15493 : 2005 | Identical |
UNE-EN ISO 15493:2004 | Identical |
ISO 15493:2003 | Identical |
NBN EN ISO 15493 : 2003 | Identical |
BS EN 15014:2007 | Plastics piping systems. Buried and above ground systems for water and other fluids under pressure. Performance characteristics for pipes, fittings and their joints |
BS 8558:2015 | Guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages. Complementary guidance to BS EN 806 |
BS 6700(2006) : 2006 | DESIGN, INSTALLATION, TESTING AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - SPECIFICATION |
11/30228295 DC : 0 | BS 8558 - GUIDE TO THE DESIGN, INSTALLATION, TESTING, OPERATION AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - COMPLEMENTARY GUIDANCE TO BS EN 806 |
15/30299694 DC : 0 | BS 8558 - GUIDE TO THE DESIGN, INSTALLATION, TESTING AND MAINTENANCE OF SERVICES SUPPLYING WATER FOR DOMESTIC USE WITHIN BUILDINGS AND THEIR CURTILAGES - COMPLEMENTARY GUIDANCE TO BS EN 806 |
BS 8558:2011 | Guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages. Complementary guidance to BS EN 806 |
EN 15014:2007 | Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints |
ISO 16135:2006 | Industrial valves Ball valves of thermoplastics materials |
ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
EN ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009) |
ISO/TR 10358:1993 | Plastics pipes and fittings Combined chemical-resistance classification table |
ISO 10241:1992 | International terminology standards Preparation and layout |
ISO 2507-2:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes |
ISO 15494:2015 | Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) — Metric series for specifications for components and the system |
EN ISO 1158:1998 | Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content (ISO 1158:1998) |
ISO 265-1:1988 | Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U) |
ISO 2507-1:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method |
ISO 3127:1994 | Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method |
ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
ISO 3:1973 | Preferred numbers Series of preferred numbers |
EN 743 : 1994 | PLASTICS PIPING AND DUCTING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF THE LONGITUDINAL REVERSION |
EN ISO 9080:2012 | Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012) |
EN 802:1994 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing |
EN 763 : 1994 | PLASTICS PIPING AND DUCTING SYSTEMS - INJECTION MOULDED THERMOPLASTICS FITTINGS - TEST METHOD FOR VISUALLY ASSESSING EFFECTS OF HEATING |
ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
ISO 12092:2000 | Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure Resistance to internal pressure Test method |
EN 1778:1999 | Characteristic values for welded thermoplastics constructions - Determination of allowable stresses and moduli for design of thermoplastics equipment |
EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
ISO 15853:1999 | Thermoplastics materials Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for injection moulding |
ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
ISO 472:2013 | Plastics — Vocabulary |
ISO 9853:1991 | Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings for pressure pipe systems — Crushing test |
EN 727:1994 | Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST) |
ISO 2505-1:1994 | Thermoplastics pipes Longitudinal reversion Part 1: Determination methods |
ISO 1158:1998 | Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content |
ISO 16138:2006 | Industrial valves Diaphragm valves of thermoplastics materials |
ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
ISO 9311-1:2005 | Adhesives for thermoplastic piping systems — Part 1: Determination of film properties |
EN 744:1995 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
ISO 16137:2006 | Industrial valves Check valves of thermoplastics materials |
ISO 9001:2015 | Quality management systems — Requirements |
EN 580:2003 | Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT) |
ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
ISO 16136:2006 | Industrial valves Butterfly valves of thermoplastics materials |
ISO 3514:1976 | Chlorinated polyvinyl chloride (CPVC) pipes and fittings — Specification and determination of density |
ISO/TR 16913:1999 | Plastics pipes and fittings — Definitions of types of test |
ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
ISO 16139:2006 | Industrial valves Gate valves of thermoplastics materials |
ISO 21787:2006 | Industrial valves Globe valves of thermoplastics materials |
EN 12107 : 1997 | PLASTICS PIPING SYSTEM - INJECTION MOULDED THERMOPLASTICS FITTINGS, VALVES AND ANCILLARY EQUIPMENT - DETERMINATION OF THE LONG-TERM HYDROSTATIC STRENGTH OF THERMOPLASTICS MATERIALS FOR INJECTION MOULDING OF PIPING COMPONENTS |
ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
EN ISO 306:2013 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
ISO 9852:2007 | Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method |
1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
ISO 727-1:2002 | Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure — Part 1: Metric series |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.