CSA C22.2 No. 62282-2 :2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FUEL CELL TECHNOLOGIES - PART 2: FUEL CELL MODULES
Hardcopy , PDF
15-04-2018
English
01-01-2013
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Type tests
6 Routine tests
7 Markings and instructions
Annex A (informative) - Additional information for the
performance and evaluation of the tests
Annex B (informative) - List of notes concerning particular
conditions in certain countries
Bibliography
Specifies the minimum requirements for safety and performance of fuel cell modules and applies to fuel cell modules with the following electrolyte chemistry: - alkaline; - polymer electrolyte (including direct methanol fuel cells); - phosphoric acid; - molten carbonate; - solid oxide; and - aqueous solution of salts.
| DocumentType |
Standard
|
| Pages |
116
|
| ProductNote |
Reconfirmed EN
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| IEC 60079-10:2002 | Electrical apparatus for explosive gas atmospheres - Part 10: Classification of hazardous areas |
| CAN/CSA-C22.2 NO. 61508-2:17 | Functional safety of electrical/electronic/programmable electronic safety-related systems — Part 2: Requirements for electrical/electronic/programmable electronic safety-related systems (Adopted IEC 61508-2:2010, second edition, 2010-04, with Canadian deviations) | Sécurité fonctionnelle des systèmes électriques/électroniques/électroniques programmables relatifs à la sécurité — Partie 2 : Exigences pour les systèmes électriques/électroniques/électroniques programmables relatifs à la sécurité (norme IEC 61508-2:2010 adoptee, deuxième édition, 2010-04, avec exigences propres au Canada) |
| CSA B51 : 2014 | BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC TS 62282-1:2013 | Fuel cell technologies - Part 1: Terminology |
| ISO 4672:1997 | Rubber and plastics hoses Sub-ambient temperature flexibility tests |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| IEC 60079-20-1:2010 | Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data |
| CSA/ANSI PRD 1 : 2013(R2018) | PRESSURE RELIEF DEVICES FOR NATURAL GAS VEHICLE (NGV) FUEL CONTAINERS |
| IEC 62040-1:2017 EXV | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS |
| CGA 12.6 : M94(R1999) | VEHICLE REFUELLING APPLIANCES |
| EN 50178:1997 | Electronic equipment for use in power installations |
| CSA C22.2 No. 65 : 2013 | WIRE CONNECTORS |
| CSA C22.2 No. 60529 : 2016 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) |
| SAE J1739_200901 | Potential Failure Mode and Effects Analysis in Design (Design FMEA), Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA) |
| CSA E60730.1 : 2015 | Automatic electrical controls for household and similar use — Part 1: General requirements |
| CSA C22.2 No. 301 : 2016 | INDUSTRIAL ELECTRICAL MACHINERY |
| IEC 62282-3-100:2012 | Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety |
| CAN/CSA-C22.2 NO. 61508-1:17 | Functional safety of electrical/electronic/programmable electronic safety-related systems — Part 1: General requirements (Adopted IEC 61508-1:2010, second edition, 2010-04, with Canadian deviations) | Sécurité fonctionnelle des systèmes électriques/électroniques/électroniques programmables relatifs à la sécurité — Partie 1 : Exigences générales (norme IEC 61508-1:2010 adoptée, deuxième édition, 2010-04, avec exigences propres au Canada) |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| BS EN 13184:2001 | Non-destructive testing. Leak testing. Pressure change method |
| ISO 1402:2009 | Rubber and plastics hoses and hose assemblies Hydrostatic testing |
| CSA C22.2 No. 107.1 : 2016 | POWER CONVERSION EQUIPMENT |
| ISO 1307:2006 | Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses |
| CAN/CSA-C22.2 NO. 61508-3:17 | Functional safety of electrical/electronic/programmable electronic safety-related systems — Part 3: Software requirements (Adopted IEC 61508-3:2010, second edition, 2010-04, with Canadian deviations) | Sécurité fonctionnelle des systèmes électriques/électroniques/électroniques programmables relatifs à la sécurité — Partie 3 : Exigences concernant les logiciels (norme IEC 61508-3:2010 adoptée, deuxième édition, 2010-04, avec exigences propres au Canada) |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| ISO 1436:2017 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 23550:2011 | Safety and control devices for gas burners and gas-burning appliances General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.