DIN EN 1870-19:2014-03
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
Available format(s)
Hardcopy , PDF
Superseded date
07-03-2021
Language(s)
German, English
Published date
01-01-2014
Important note : Users cannot be edited or removed once added to your Multi user PDF.
National foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (normative) - Stability test
Annex B (normative) - Test for rigidity of
building site saws
Annex C (normative) - Saw spindle dimensional
tolerances
Annex D (normative) - Riving knife mounting
strength test
Annex E (normative) - Riving knife lateral
stability test
Annex F (normative) - Minimum dimensions
of the machine table, extension table
and insert
Annex G (normative) - Saw blade guard
stability test
Annex H (normative) - Impact test method
for guards
Annex I (normative) - Braking tests
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
Describes all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit) and building site saws, hereinafter referred to as 'machines', designed to cut solid wood, chipboard, fibreboard, plywood and also these materials, if they are covered with plastic edging and/or plastic/light alloy laminates, when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
| DevelopmentNote |
Supersedes DIN EN 1870-1. (03/2014)
|
| DocumentType |
Standard
|
| Pages |
94
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| EN 1870-19:2013 | Identical |
| PREN 1870-19 : DRAFT 2011 | Identical |
| EN 1005-4:2005+A1:2008 | Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery |
| EN 50525-2-21:2011/AC:2013 | ELECTRIC CABLES - LOW VOLTAGE ENERGY CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V (U[0]/U) - PART 2-21: CABLES FOR GENERAL APPLICATIONS - FLEXIBLE CABLES WITH CROSSLINKED ELASTOMERIC INSULATION |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN 60745-1:2009/A11:2010 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| IEC 61029-2-1:1993 | Safety of transportable motor-operated electric tools - Part 2: Particular requirements for circular saws |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 60745-2-5:2010 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 2-5: PARTICULAR REQUIREMENTS FOR CIRCULAR SAWS |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 61800-5-2:2017 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN 1870-5 : 2002 | SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES |
| EN ISO 3743-2:2009 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 3743-2:1994 | Acoustics Determination of sound power levels of noise sources using sound pressure Engineering methods for small, movable sources in reverberant fields Part 2: Methods for special reverberation test rooms |
| ISO 7960:1995 | Airborne noise emitted by machine tools Operating conditions for woodworking machines |
| EN 1093-9:1998+A1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 9: Pollutant concentration parameter, room method |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 614-2:2000+A1:2008 | Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks |
| EN 50370-2:2003 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1005-1:2001+A1:2008 | Safety of machinery - Human physical performance - Part 1: Terms and definitions |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| EN 12779:2015 | Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN 61029-2-1:2012 | Safety of transportable motor-operated electric tools - Part 2-1: Particular requirements for circular saw benches |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| IEC 61029-1:1990 | Safety of transportable motor-operated electric tools - Part 1: General requirements |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60745-2-5:2010 | Hand-held motor-operated electric tools - Safety - Part 2-5: Particular requirements for circular saws |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| IEC 60439-1:1999+AMD1:2004 CSV | Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| IEC 60745-1:2006 | Hand-held motor-operated electric tools - Safety - Part 1: General requirements |
| EN 60439-1:1999/A1:2004 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN 847-1:2017 | Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades |
| EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 61029-1:2009/A11:2010 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 1005-3:2002+A1:2008 | Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| EN 50370-1:2005 | Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| ISO 11204:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
| EN 1093-11:2001+A1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index |
| IEC 61800-5-2:2016 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| ISO 3743-1:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for small movable sources in reverberant fields Part 1: Comparison method for a hard-walled test room |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.