DIN EN 60687 : 1994
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ALTERNATING-CURRENT STATIC WATT-HOUR METERS FOR ACTIVE ENERGY (CLASSES 0.2 S AND 0.5 S)
01-11-2003
12-01-2013
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
3.1 Allgemeine Begriffe
3.2 Begriffe für die Funktionseinheiten
3.3 Begriffe der mechanischen Bauteile
3.4 Begriffe der Isolation
3.5 Begriffe der Zähler-Nenngrössen
3.6 Begriffe der Einflussgrössen
3.7 Begriffe von Prüfungen
4 Anforderungen
4.1 Genormte elektrische Werte
4.2 Mechanische Anforderungen
4.3 Klimatische Bedingungen
4.4 Elektrische Anforderungen
4.5 Elektromagnetische Verträglichkeit (EMV)
4.6 Anforderungen an die Genauigkeit
5 Prüfungen und Prüfbedingungen
5.1 Allgemeine Prüfverfahren
5.2 Prüfung der mechanischen Anforderungen
5.3 Prüfung der klimatischen Einflüsse
5.4 Prüfung der elektrischen Anforderungen
5.5 Prüfung der elektromagnetischen Verträglichkeit
(EMV) Luftfeuchte
5.6 Prüfungen auf Einhalten der Genauigkeitsanforderungen
Anhänge
Anhang A (normativ) Beziehung zwischen
Umgebungslufttemperatur und relativ
Anhang B (normativ) Wellenform der Spannung für die
Prüfungen des Einflusses von
Spannungsabsenkungen und kurzen
Spannungsunterbrechungen
Anhang C (normativ) Elektromagnet für die Prüfung der
Störfestigkeit gegen äussere magnetische
Gleichfelder
Anhang D (informativ) Prüfplan
Anhang ZA (normativ) Besondere nationale Bedingungen
Anhang ZB (normativ) Andere in dieser Norm zitierte
internationale Publikationen mit den
Verweisungen der entsprechenden europäischen
Publikationen
Deals with the measurement (by static watt hour meters of accuracy classes 0,2 S and 0,5 S) of alternating current electrical active energy of a frequency between 45Hz to 65 Hz and to their type tests only. Applies transformer operated static meters for indoor application consisting of one or more measuring elements and registers enclosed together in the same case. Also applies to test outputs, operation indicators and meters that measure energy in both directions. Does not apply to: portable meters and meters for outdoor use; watt hour meters where the voltage across the connection terminals exceeds 600 V (line to line voltage for meters for polyphase systems); data interface to the register of the meter; reference meters.
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN EN 60687 : 1993 | Identical |
| SN EN 60687 : 1992 | Identical |
| EN 60687:1992/corrigendum:1993 | Identical |
| NF EN 60687 : 1993 | Identical |
| IEC 60687:1992 | Identical |
| I.S. EN 60687:1993 | Identical |
| UNE-EN 60687:1994 | Identical |
| VDE 0418-8 : 1994 | Corresponds |
| BS EN 60687:1993 | Identical |
| VDE 0418-8 : 1994 | Identical |
| DIN EN 62053-61 : 1999 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 61: POWER CONSUMPTION AND VOLTAGE REQUIREMENTS |
| VDE 0418-3-61 : 1999 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 61: POWER CONSUMPTION AND VOLTAGE REQUIREMENTS |
| VDE 0418-3-31 : 1999 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 31: PULSE OUTPUT DEVICES FOR ELECTROMECHANICAL AND ELECTRONIC METERS (TWO WIRES ONLY) |
| DIN EN 62053-31 : 1999 | ELECTRICITY METERING EQUIPMENT (A.C.) - PARTICULAR REQUIREMENTS - PART 31: PULSE OUTPUT DEVICES FOR ELECTROMECHANICAL AND ELECTRONIC METERS (TWO WIRES ONLY) |
| VDE 0418-7 : 2001 | ALTERNATING CURRENT ELECTRONIC WATT-HOUR METERS FOR ACTIVE ENERGY (CLASSES 1 AND 2) |
| DIN IEC 60038 : 2002 | IEC STANDARD VOLTAGES |
| IEC 60695-2-1:1991 | Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
| DIN IEC 60068-2-27:1989-08 | ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TESTS; TEST Ea AND GUIDANCE; SHOCK |
| DIN IEC 60068-2-1:1985-08 | ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TESTS; TESTS A: COLD |
| DIN VDE 0110-1 : 1997 | INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 1: PRINCIPLES, REQUIREMENTS AND TESTS |
| DIN IEC 60068-2-30:1986-09 | ELECTRICAL ENGINEERING - BASIC ENVIRONMENTAL TESTING PROCEDURES - TEST DB AND GUIDANCE - DAMP HEAT, CYCLIC (12 + 12 HOUR CYCLE) |
| IEC 60521:1988 | Class 0.5, 1 and 2 alternating-current watthour meters |
| DIN VDE 0418-12 : 1988 | ELEKTRIZITAETSZAEHLER - WECHSELSTROM-WIRKVERBRAUCHSZAEHLER FUER MESSWANDLERANSCHLUSS - GENAUIGKEITSKLASSE 0,5, 1 UND 2 |
| IEC TR 60736:1982 | Testing equipment for electrical energy meters |
| ISO 75:1987 | Plastics and ebonite Determination of temperature of deflection under load |
| DIN IEC 60068-2-6:1990-06 | ELECTRICAL ENGINEERING; BASIC ENVIRONMENTAL TESTING PROCEDURES; TEST Fc AND GUIDANCE: VIBRATION (SINUSOIDAL) |
| DIN IEC 60359:1993-09 | EXPRESSION OF THE PERFORMANCE OF ELECTRICAL AND ELECTRONIC MEASURING EQUIPMENT |
| IEC 60801-4:1988 | Electromagnetic compatibility for industrial-process measurement and control equipment - Part 4: Electrical fast transient/burst requirements |
| DIN IEC 60068-2-11:1982-08 | BASIC ENVIRONMENTAL TESTING PROCEDURES - PART 2: TESTS - TEST KA: SALT MIST |
| IEC 60817:1984 | Spring-operated impact-test apparatus and its calibration |
| IEC 60801-1:1984 | Electromagnetic compatibility for industrial-process measurement and control equipment. Part 1: General introduction |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| DIN 40050-9:1993-05 | ROAD VEHICLES; DEGREES OF PROTECTION (IP-CODE); PROTECTION AGAINST FOREIGN OBJECTS, WATER AND CONTACT; ELECTRICAL EQUIPMENT |
| DIN IEC 60721-3-3:1990-04 | ELECTRICAL ENGINEERING; CLASSIFICATION OF ENVIRONMENTAL CONDITIONS; CLASSIFICATION OF GROUPS OF ENVIRONMENTAL PARAMETERS AND THEIR SEVERITIES; STATIONARY USE AT WEATHER PROTECTED LOCATIONS |
| IEC 60801-3:1984 | Electromagnetic compatibility for industrial-process measurement and control equipment - Part 3: Radiated electromagnetic field requirements |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| DIN IEC 60068-2-2:1980-03 | BASIC ENVIRONMENTAL TESTING PROCEDURES; TESTS; TESTS B: DRY HEAT |
| IEC 61036:1996+AMD1:2000 CSV | Alternating current static watt-hour meters for active energy (classes 1 and 2) |
| IEC 60801-2:1991 | Electromagnetic compatibility for industrial-process measurement and control equipment - Part 2: Electrostatic discharge requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.