DIN EN ISO 178 E : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013)
Hardcopy , PDF
04-09-2019
English
01-01-2013
National foreword
National Annex NA (informative) - Bibliography
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Test machine
6 Test specimens
7 Atmosphere for conditioning and testing
8 Procedure
9 Calculation and expression of results
10 Precision
11 Test report
Annex A (informative) - Precision statement
Annex B (informative) - Influence of changes in test
speed on the measured values of flexural properties
Bibliography
Describes a method for determining the flexural properties of rigid and semi-rigid plastics under defined conditions.
DevelopmentNote |
Supersedes DIN 53452 E and DIN 53457 E (08/2002)
|
DocumentType |
Standard
|
Pages |
27
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
UNI EN ISO 178 : 2013 | Identical |
NS EN ISO 178 : 2010 AMD 1 2013 | Identical |
EN ISO 178:2010/A1:2013 | Identical |
ISO 178:2010 | Identical |
SN EN ISO 178 : 2011 AMD 1 2013 | Identical |
NF EN ISO 178 : 2011 AMD 1 2013 | Identical |
BS EN ISO 178 : 2010 | Identical |
ONORM EN ISO 178 : 2013 | Identical |
I.S. EN ISO 178:2010 | Identical |
NBN EN ISO 178 : 2011 AMD 1 2013 | Identical |
NEN EN ISO 178 : 2010 AMD 1 2013 | Identical |
EN ISO 178:2019 | Identical |
DIN EN ISO 25137-2 E : 2017 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
DIN EN ISO 3673-2 E : 2012 | PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012) |
DIN EN ISO 3672-2:2002-07 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
DIN EN ISO 17855-2 E : 2016 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
DIN ISO 11040-4 E : 2017 | PREFILLED SYRINGES - PART 4: GLASS BARRELS FOR INJECTABLES AND STERILIZED SUBASSEMBLED SYRINGES READY FOR FILLING (ISO 11040-4:2015) |
DIN EN 12864 E : 2006 AMD 3 2010 | LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
DIN EN ISO 11833-1:2012-11 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
DIN 16833:2009-09 | Pipes of raised-temperature-resistance polyethylene (PE-RT) - PE-RT Type I and PE-RT Type II - General quality requirements, testing |
DIN 28090-3:2014-11 | STATIC GASKETS FOR FLANGE CONNECTIONS - GASKETS MADE FROM SHEETS - PART 3: CHEMICAL RESISTANCE TEST PROCEDURES |
DIN EN ISO 12215-5:2014-10 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014) |
DIN EN ISO 9988-2 E : 2015 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 9988-2:2006) |
DIN EN ISO 3672-2 E : 2002 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
DIN EN ISO 20028-2 E : 2017 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
DIN EN ISO 14910-2 E : 2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
DIN EN ISO 19069-2 E : 2016 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
DIN EN ISO 80369-7 E : 2017 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS (ISO 80369-7:2016, CORRECTED VERSION 2016-12-01) |
DIN EN ISO 80369-7:2017-10 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
DIN EN ISO 14910-2:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
DIN ISO 11040-4:2017-07 | PREFILLED SYRINGES - PART 4: GLASS BARRELS FOR INJECTABLES AND STERILIZED SUBASSEMBLED SYRINGES READY FOR FILLING (ISO 11040-4:2015) |
ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
DIN EN ISO 9513 E : 2013 | METALLIC MATERIALS - CALIBRATION OF EXTENSOMETER SYSTEMS USED IN UNIAXIAL TESTING (ISO 9513:2012 + COR 1:2013) |
ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
DIN EN ISO 295 E : 2004 | PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOSETTING MATERIALS |
ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
ISO 1209-2:2007 | Rigid cellular plastics Determination of flexural properties Part 2: Determination of flexural strength and apparent flexural modulus of elasticity |
ISO 472:2013 | Plastics Vocabulary |
DIN EN ISO 291 E : 2008 | PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING AND TESTING |
ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
ISO 14125:1998 | Fibre-reinforced plastic composites — Determination of flexural properties |
ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
DIN EN ISO 293 E : 2005 | PLASTICS - COMPRESSION MOULDING TEST SPECIMENS OF THERMOPLASTIC MATERIALS |
ISO 20753:2008 | Plastics Test specimens |
ISO 16012:2015 | Plastics Determination of linear dimensions of test specimens |
ISO 1209-1:2007 | Rigid cellular plastics Determination of flexural properties Part 1: Basic bending test |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.