• Shopping Cart
    There are no items in your cart

DIN EN ISO 527-1:2012-06

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL PRINCIPLES (ISO 527-1:2012)

Available format(s)

Hardcopy , PDF

Superseded date

21-12-2019

Superseded by

DIN EN ISO 527-1:2019-12

Language(s)

English, German

Published date

01-01-2012

€124.21
Excluding VAT

National foreword
National Annex NA (informative) - Bibliography
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Principle and methods
5 Apparatus
6 Test specimens
7 Number of test specimens
8 Conditioning
9 Procedure
10 Calculation and expression of results
11 Precision
12 Test report
Annex A (informative) - Determination of strain at yield
Annex B (informative) - Extensometer accuracy for the
        determination of Poisson's ratio
Annex C (normative) - Calibration requirements for the
        determination of the tensile modulus
Bibliography

Defines the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.

DevelopmentNote
Together with DIN EN ISO 527-2 E; supersedes DIN 53455 E. (12/1999) Supersedes DIN 53457 E (08/2002)
DocumentType
Standard
Pages
30
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy
Supersedes

DIN ISO 5355:2006-05 ALPINE SKI-BOOTS - REQUIREMENTS AND TEST METHODS
DIN EN ISO 527-5:2010-01 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
DIN EN ISO 22007-4:2012-04 PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 4: LASER FLASH METHOD (ISO 22007-4:2017)
DIN EN ISO 11296-7:2013-05 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011)
DIN EN ISO 15013:2008-01 Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007); German version EN ISO 15013:2007
DIN 34811:1999-09 CROSS- RECESSED FLAT HEAD PLASTIC SCREWS
DIN EN ISO 3672-2:2002-07 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
DIN 53504:2009-10 TESTING OF RUBBER - DETERMINATION OF TENSILE STRENGTH AT BREAK, TENSILE STRESS AT YIELD, ELONGATION AT BREAK AND STRESS VALUES IN A TENSILE TEST
DIN 53363:2003-10 Determining the tear resistance of plastic film and sheeting by the trouser tear method
DIN EN 12864 E : 2006 AMD 3 2010 LOW PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES
DIN EN ISO 11963:2013-03 PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS (ISO 11963:2012)
DIN 34813:1999-09 CROSS- RECESSED CHEESE HEAD PLASTIC SCREWS
DIN 34812:1999-09 CROSS- RECESSED PAN HEAD PLASTIC SCREWS
DIN ISO 9523:2016-05 TOURING SKI-BOOTS FOR ADULTS - INTERFACE WITH TOURING SKI-BINDINGS - REQUIREMENTS AND TEST METHODS (ISO 9523:2015)
DIN EN ISO 527-2:2012-06 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
DIN 30678:2013-09 Polypropylene coatings on steel pipes and fittings - Requirements and testing
DIN EN ISO 12215-5:2014-10 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014)

ISO 23529:2016 Rubber General procedures for preparing and conditioning test pieces for physical test methods
ISO 1926:2009 Rigid cellular plastics Determination of tensile properties
ISO 9513:2012 Metallic materials — Calibration of extensometer systems used in uniaxial testing
ISO 2602:1980 Statistical interpretation of test results Estimation of the mean Confidence interval
ISO 291:2008 Plastics Standard atmospheres for conditioning and testing
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
ISO 20753:2008 Plastics Test specimens
DIN EN ISO 291:2008-08 PLASTICS - STANDARD ATMOSPHERES FOR CONDITIONING AND TESTING
ISO 16012:2015 Plastics Determination of linear dimensions of test specimens
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.