EN 117000:1991
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
Generic Specification: Solid state all-or-nothing relays of assessed quality - Generic data and methods of test
15-04-1992
15-10-1991
Foreword
Preface
SECTION 1 SCOPE
SECTION 2 GENERAL
2.1 Order of precedence
2.2 Related documents
2.3 Units, symbols and terminology
2.4 Preferred values
2.5 Marking
SECTION 3 TERMS AND DEFINITIONS
3.1 Construction
3.2 Type of relays
3.3 General terms
3.4 Prefixes for the values applicable to
relays
3.5 Control signal values
3.6 Output values
3.7 Terms relating to times
SECTION 4 QUALITY ASSESSMENT PROCEDURES
4.1 Primary stage of manufacture
4.2 Structurally similar components
4.3 Qualification approval procedures
4.4 Quality conformance inspection
4.5 Division into groups
4.6 Resubmission of rejected lots
4.7 Certified test records
4.8 Delivery of relays subjected to tests
4.9 Delayed delivery
4.10 Supplementary procedures for deliveries
4.11 Unchecked parameters
4.12 Release for delivery before the completion
of Group B tests
SECTION 5 TEST AND MEASUREMENT PROCEDURE
5.1 General
5.2 Alternative methods
5.3 Precision of measurement
5.4 Requirements in detail specifications
5.5 Standard conditions for testing
5.6 Visual inspection and check of dimensions
5.7 Mass
5.8 Terminal identification
5.9 "Must operate" and :"Must release" control
signal current and voltage ION, VON, VO
5.10 Peak on-state voltage VTM
5.11 Zero turn-on voltage VTO
5.12 Surge (Non-repetitive) on-state current ITSM
5.13 Surge (Non-repetitive) on-state current ITSM
(with rapid rate of rise of reverse voltage)
5.14 Critical rate of rise of on-state current
dI/dt
5.15 Critical rate of rise of commutating
voltage dV/dt
5.16 Critical rate of rise of off-state voltage
dV/dt
5.17 Off-state current ID
5.18 Repetitive peak off-state voltage VDRM
5.19 Non-repetitive peak off-state voltage VDSM
5.20 Input circuit resistance
5.21 Dielectric test
5.22 Insulation resistance
5.23 Climatic sequence
5.24 Damp heat steady state
5.25 Rapid change of temperature
5.26 Accelerated thermal cycling
5.27 Enclosure
5.28 Corrosive atmosphere
5.29 Mould growth
5.30 Robustness of terminals
5.31 Soldering
5.32 Shock
5.33 Bump
5.34 Vibration
5.35 Acceleration
5.36 Electrical endurance
5.37 Thermal endurance
5.38 Voltage blocking
5.39 Resistance to solvents
5.40 Fire hazard
5.41 Radio frequency interference
(under consideration)
Gives test and measuring methods for selection to be used in detail specifications for solid state relays of assessed quality. In addition, it defines the quality assurance procedures.
| Committee |
CLC/SR 94
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Withdrawn
|
| Standards | Relationship |
| DIN EN 117000:1992-02 | Identical |
| CECC 17000 : 1990 | Identical |
| PN EN 117000 : DEC 2002 | Identical |
| UNE-EN 117000:1991 | Identical |
| BS EN 117000:1997 | Identical |
| I.S. EN 117000:1994 | Identical |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60695-2-1:1991 | Fire hazard testing - Part 2: Test methods - Section 1: Glow-wire test and guidance |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| IEC 60068-2-11:1981 | Basic environmental testing procedures - Part 2-11: Tests - Test Ka: Salt mist |
| IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
| IEC 60068-2-3:1969 | Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state |
| ISO 8601:2004 | Data elements and interchange formats Information interchange Representation of dates and times |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| IEC 60068-2-10:2005 | Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60255-5:2000 | Electrical Relays - Part 5: Insulation coordination for measuring relays and protection equipment - Requirements and tests |
| IEC 60255-1:1967 | Electrical relays - Part 1: Instantaneous all-or-nothing relays |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| IEC 60443:1974 | Stabilized supply apparatus for measurement |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 60144:1963 | Degrees of protection of enclosures for low-voltage switchgear and controlgear |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| CECC 00007 : 1978 | BASIC SPECIFICATION: SAMPLING PLANS AND PROCEDURES FOR INSPECTION BY ATTRIBUTES |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.