![header thumbnail](/images/img-default-logo.png)
EN 1459-2:2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
![header thumbnail](/images/img-default-logo.png)
Rough-terrain trucks - Safety requirements and verification - Part 2: Slewing variable-reach trucks
14-11-2022
16-09-2015
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Safety requirements and/or protective measures
5 Verification of requirements and safety measures
6 Information for use
Annex A (informative) - List of significant hazards
Annex B (informative) - Consistency of motions
Annex C (normative) - Rules for the construction and
layout of pedals
Annex D (informative) - Regular and occasional loads
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2006/42/EC
Bibliography
This European Standard specifies the general safety requirements of slewing variable-reach rough-terrain trucks (here-after referred to as trucks), consisting of a lower chassis with a slewing upper structure equipped with a telescopic lifting means (pivoted boom), on which a load handling device (e.g. carriage and fork arms) is typically fitted.Fork arms are covered by this European Standard and considered to be parts of the truck.This European Standard deals with all significant hazards, hazardous situations and events relevant to the trucks when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A) with the exception of hazards listed in 1.3 and 1.4.This European Standard does not apply to:-variable-reach rough terrain trucks covered by prEN 1459-1 (non-slewing);-industrial variable-reach trucks covered by prEN ISO 3691 2;-lorry-mounted variable-reach trucks;-variable reach trucks fitted with tilting or elevating operator position;-mobile cranes covered by EN 13000;-machines designed primarily for earth moving, such as loaders and dozers, even if their buckets and blades are replaced with forks (see EN 474 series);-trucks designed primarily with variable length load suspension elements (e.g., chain, ropes) from which the load may swing freely in all directions;-trucks designed primarily for container handling;-trucks on tracks;-attachments (prEN 1459-5).This European Standard does not address hazards linked to:-hybrid power systems;-gas power system;-trucks equipped with gasoline engine;-battery power system;-tractor specific devices (e.g. PTO).This European Standard does not address hazards which may occur when:a)handling suspended loads which may swing freely (additional requirements are given in prEN 1459-4);b)using trucks on public roads;c)operating in potentially explosive atmospheres;d)operating underground;e)when towing trailers;f)fitted with a personnel work platform (additional requirements are given in EN 1459-3).
Committee |
CEN/TC 150
|
DevelopmentNote |
Supersedes PREN 1459-2. (09/2015)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
DS EN 1459-2 : 2015 | Identical |
UNE-EN 1459-2:2016 | Identical |
DIN EN 1459-2:2016-05 | Identical |
I.S. EN 1459-2:2015 | Identical |
ÖNORM EN 1459-2: 2019 04 15 | Identical |
PN EN 1459-2 : 2015 | Identical |
NS EN 1459-2 : 2015 | Identical |
ONORM EN 1459-2 : 2016 | Identical |
UNI EN 1459-2 : 2015 | Identical |
BS EN 1459-2 : 2015 | Identical |
NEN EN 1459-2 : 2015 | Identical |
SN EN 1459-2 : 2016 | Identical |
NF EN 1459-2 : 2015 | Identical |
NBN EN 1459-2 : 2015 | Identical |
17/30332527 DC : DRAFT JAN 2017 | BS EN 1459-5 - ROUGH-TERRAIN TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - PART 5 - ATTACHMENTS AND ATTACHMENT INTERFACE |
BS EN 1459-1:2017 | Rough-terrain trucks. Safety requirements and verification Variable-reach trucks |
EN 1459-1:2017 | Rough-terrain trucks - Safety requirements and verification - Part 1: Variable-reach trucks |
BS EN 16796-1:2016 | Energy efficiency of Industrial trucks. Test methods General |
I.S. EN 1459-1:2017 | ROUGH-TERRAIN TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - PART 1: VARIABLE-REACH TRUCKS |
I.S. EN 16796-1:2016 | ENERGY EFFICIENCY OF INDUSTRIAL TRUCKS - TEST METHODS - PART 1: GENERAL |
PREN 1459-7 : DRAFT 2017 | ROUGH-TERRAIN TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - PART 7: TEST METHOD AND DETERMINATION OF NOISE EMISSION |
UNE-EN 16796-1:2017 | Energy efficiency of Industrial trucks - Test methods - Part 1: General |
EN 16796-1:2016 | Energy efficiency of Industrial trucks - Test methods - Part 1: General |
17/30364315 DC : 0 | BS EN 1459-7 - ROUGH-TERRAIN TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - PART 7: TEST METHOD AND DETERMINATION OF NOISE EMISSION |
UNE-EN 1459-1:2018 | Rough-terrain trucks - Safety requirements and verification - Part 1: Variable-reach trucks |
ISO 3449:2005 | Earth-moving machinery — Falling-object protective structures — Laboratory tests and performance requirements |
EN ISO 2860:2008 | Earth-moving machinery - Minimum access dimensions (ISO 2860:1992) |
ISO 10532:1995 | Earth-moving machinery Machine-mounted retrieval device Performance requirements |
EN ISO 3164:2013 | Earth-moving machinery - Laboratory evaluations of protective structures - Specifications for deflection-limiting volume (ISO 3164:2013) |
ISO 3164:2013 | Earth-moving machinery — Laboratory evaluations of protective structures — Specifications for deflection-limiting volume |
ISO 10263-5:2009 | Earth-moving machinery Operator enclosure environment Part 5: Windscreen defrosting system test method |
ISO 4302:2016 | Cranes — Wind load assessment |
EN ISO 6683:2008 | Earth-moving machinery - Seat belts and seat belt anchorages - Performance requirements and tests (ISO 6683:2005) |
ISO 13333:1994 | Earth-moving machinery Dumper body support and operator's cab tilt support devices |
ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
ISO 15817:2012 | Earth-moving machinery — Safety requirements for remote operator control systems |
ISO 7096:2000 | Earth-moving machinery Laboratory evaluation of operator seat vibration |
ISO 3411:2007 | Earth-moving machinery Physical dimensions of operators and minimum operator space envelope |
ISO 6683:2005 | Earth-moving machinery Seat belts and seat belt anchorages Performance requirements and tests |
EN ISO 3449:2008 | Earth-moving machinery - Falling-object protective structures - Laboratory tests and performance requirements (ISO 3449:2005) |
EN ISO 3411:2007 | Earth-moving machinery - Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007) |
EN ISO 3457:2008 | Earth-moving machinery - Guards - Definitions and requirements (ISO 3457:2003) |
ISO 22915-20:2008 | Industrial trucks — Verification of stability — Part 20: Additional stability test for trucks operating in the special condition of offset load, offset by utilization |
ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
ISO 5353:1995 | Earth-moving machinery, and tractors and machinery for agriculture and forestry Seat index point |
ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
ISO 12508:1994 | Earth-moving machinery Operator station and maintenance areas Bluntness of edges |
EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
ISO 22915-10:2008 | Industrial trucks — Verification of stability — Part 10: Additional stability test for trucks operating in the special condition of stacking with load laterally displaced by powered devices |
ISO 21507:2010 | Earth-moving machinery Performance requirements for non-metallic fuel tanks |
ISO 11862:1993 | Earth-moving machinery — Auxiliary starting aid electrical connector |
EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
ISO 12509:2004 | Earth-moving machinery — Lighting, signalling and marking lights, and reflex-reflector devices |
EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
ISO 6011:2003 | Earth-moving machinery — Visual display of machine operation |
ISO 10896-1:2012 | Rough-terrain trucks Safety requirements and verification Part 1: Variable-reach trucks |
ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
EN 12895:2015 | Industrial trucks - Electromagnetic compatibility |
EN 1175-2:1998+A1:2010 | Safety of industrial trucks - Electrical requirements - Part 2: General requirements of internal combustion engine powered trucks |
ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
EN ISO 13732-1:2008 | Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006) |
EN ISO 5353:1998 | Earth-moving machinery, and tractors and machinery for agriculture and forestry - Seat index point (ISO 5353:1995) |
ISO 10263-3:2009 | Earth-moving machinery Operator enclosure environment Part 3: Pressurization test method |
ISO 3471:2008 | Earth-moving machinery — Roll-over protective structures — Laboratory tests and performance requirements |
ISO 22915-24:2015 | Industrial trucks Verification of stability Part 24: Slewing variable-reach rough-terrain trucks |
ISO 2860:1992 | Earth-moving machinery — Minimum access dimensions |
EN 15830:2012 | Rough-terrain variable reach trucks - Visibility - Test methods and verification |
EN 1459-3:2015 | Rough-terrain trucks - Safety requirements and verification - Part 3: Interface between the variable-reach truck and the work platform |
ISO 5006:2017 | Earth-moving machinery — Operator's field of view — Test method and performance criteria |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
ISO 4305:2014 | Mobile cranes — Determination of stability |
EN 842:1996+A1:2008 | Safety of machinery - Visual danger signals - General requirements, design and testing |
EN 13309:2010 | Construction machinery - Electromagnetic compatibility of machines with internal power supply |
EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
EN 62061:2005/A2:2015 | SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015) |
ISO 10263-2:2009 | Earth-moving machinery Operator enclosure environment Part 2: Air filter element test method |
ISO 3457:2003 | Earth-moving machinery — Guards — Definitions and requirements |
EN ISO 3471:2008 | Earth-moving machinery - Roll-over protective structures - Laboratory tests and performance requirements (ISO 3471:2008) |
ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
EN 13059:2002+A1:2008 | Safety of industrial trucks - Test methods for measuring vibration |
EN ISO 6682:2008 | Earth-moving machinery - Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989) |
ISO 6292:2008 | Powered industrial trucks and tractors Brake performance and component strength |
EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
ISO 10263-4:2009 | Earth-moving machinery Operator enclosure environment Part 4: Heating, ventilating and air conditioning (HVAC) test method and performance |
EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
CEN/TR 1459-6:2015 | Rough-terrain trucks - Safety requirements and verification - Part 6: Application of EN ISO 13849-1 to slewing and non-slewing variable-reach rough-terrain truck |
IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
EN ISO 2867:2011 | Earth-moving machinery - Access systems (ISO 2867:2011) |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
EN 12053:2001+A1:2008 | Safety of industrial trucks - Test methods for measuring noise emissions |
ISO 6016:2008 | Earth-moving machinery — Methods of measuring the masses of whole machines, their equipment and components |
ISO 2867:2011 | Earth-moving machinery Access systems |
EN 13000:2010+A1:2014 | Cranes - Mobile cranes |
ISO 9533:2010 | Earth-moving machinery Machine-mounted audible travel alarms and forward horns Test methods and performance criteria |
ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
ISO 5053-1:2015 | Industrial trucks Terminology and classification Part 1: Types of industrial trucks |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.