
EN 1807:1999+A1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by

Safety of woodworking machines - Band sawing machines
01-03-2013
02-09-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (informative) - Safe working practice
Annex B (normative) - Test for adjustable guard over
cutting area of saw blade
Annex C (normative) - Operating conditions for noise
emission measurement
Annex D (informative) - Indication of the clauses of
this European standard that
are applicable to each type
of machine covered by the
European standard
Annex E (informative) - Machines requiring special
procedures
Annex ZA (informative) - Relationship between this
European Standard and the
Essential Requirements of
EU Directive 98/37/EC
Annex ZB (informative) - Relationship between this
European Standard and the
Essential Requirements of
EU Directive 2006/42/EC
Bibliography
This document specifies all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable band sawing machines with either manual or automatic loading and/or unloading, hereinafter referred to as "machines" designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic laminate or edgings.This European Standard does not cover the hazards related to Electromagnetic Compatibility (EMC) as required by the EMC Directive 89/336/EEC of 03-05-89.This European Standard does not apply to:-hand held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench mounting;NOTE 1Hand-held motor operated electric tools are covered by the requirements of EN 60745-1:2006 together with EN 60745-2-20:2003.-transportable machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand.NOTE 2Transportable electrically driven machines are covered by the requirements of EN 61029-1:2000 together with EN 61029-2-5:2002.This European Standard does not cover the hazards arising from machining processes (e.g. milling and sawing) of related to associated machines e.g. canters and circular saws.This European Standard is primarily directed at machines which are manufactured after the date of issue of this standard.
Committee |
CEN/TC 142
|
DevelopmentNote |
1999 Edition Re-Issued in September 2009 & incorporates AMD 1 2009. (09/2009)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
DIN EN 1807:1999-10 | Identical |
BS EN 1807 : 1999 | Identical |
SN EN 1807 : 1999 + A1 2010 | Identical |
NBN EN 1807 : 1999 + A1 2009 | Identical |
NEN EN 1807 : 1999 + A1 2009 | Identical |
NS EN 1807 : 1999 + A1 2009 | Identical |
PN EN 1807 : 2001 + A1 2010 | Identical |
DIN EN 1807:2010-02 | Identical |
UNI EN 1807 : 2010 | Identical |
I.S. EN 1807:2000 | Identical |
UNE-EN 1807:2000 | Identical |
NF EN 1807 : 1999 + A1 2010 | Identical |
UNE-EN 1807:2000+A1:2010 | Identical |
EN 61029-2-5:2011/A11:2015 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS (IEC 61029-2-5:1993, MODIFIED + A1:2001, MODIFIED) |
11/30244752 DC : 0 | BS EN 61029-2-5 - SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS |
UNE-EN 61029-2-5:2012 | Safety of transportable motor-operated electric tools - Part 2-5: Particular requirements for band saws |
BS EN 61029-2-5 : 2011 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS |
12/30260302 DC : 0 | BS EN 12268 - FOOD PROCESSING MACHINERY - BAND SAW MACHINES - SAFETY AND HYGIENE REQUIREMENTS |
I.S. EN 61029-2-5:2011 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS (IEC 61029-2-5:1993, MODIFIED + A1:2001, MODIFIED) |
PREN 61029-2-5 : DRAFT 2011 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS |
EN 1005-4:2005+A1:2008 | Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery |
ISO 11202:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
ISO 3744:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for an essentially free field over a reflecting plane |
EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
CLC/TS 61496-2:2006 | Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) |
EN ISO 3743-2:2009 | Acoustics - Determination of sound power levels of noise sources using sound pressure - Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) |
ISO/TR 11688-1:1995 | Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning |
EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
ISO 7960:1995 | Airborne noise emitted by machine tools — Operating conditions for woodworking machines |
ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
EN 1005-1:2001+A1:2008 | Safety of machinery - Human physical performance - Part 1: Terms and definitions |
EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
EN 1760-1:1997+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors |
ISO 1940-1:2003 | Mechanical vibration — Balance quality requirements for rotors in a constant (rigid) state — Part 1: Specification and verification of balance tolerances |
EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
IEC 61029-1:1990 | Safety of transportable motor-operated electric tools - Part 1: General requirements |
HD 22-1 : 200S4 | CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOSETTING INSULATION - GENERAL REQUIREMENTS |
HD 21.1 : 200S4 | CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V AND HAVING THERMOPLASTIC INSULATION - GENERAL REQUIREMENTS |
EN 61029-2-5:2011/A11:2015 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 2-5: PARTICULAR REQUIREMENTS FOR BAND SAWS (IEC 61029-2-5:1993, MODIFIED + A1:2001, MODIFIED) |
ISO 3746:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Survey method using an enveloping measurement surface over a reflecting plane |
EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
EN 60947-4-1 : 2010 AMD 1 2012 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 4-1: CONTACTORS AND MOTOR-STARTERS - ELECTROMECHANICAL CONTACTORS AND MOTOR-STARTERS (IEC 60947-4-1:2009/A1:2012) |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
ISO 12100-2:2003 | Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles |
ISO 13857:2008 | Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs |
IEC 61029-2-5:1993 | Safety of transportable motor-operated electric tools - Part 2: Particular requirements for band saws |
EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
EN ISO 3743-1:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010) |
ISO 12100-1:2003 | Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology |
ISO 13850:2015 | Safety of machinery — Emergency stop function — Principles for design |
EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
EN 61029-1:2009/A11:2010 | SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS |
EN 1005-3:2002+A1:2008 | Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation |
EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
ISO 11204:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections |
IEC 61496-2:2013 | Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) |
ISO 3743-1:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for small movable sources in reverberant fields — Part 1: Comparison method for a hard-walled test room |
EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.