• There are no items in your cart

EN 60317-8:2010

Current

Current

The latest, up-to-date edition.

Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180

Published date

21-05-2010

Sorry this product is not available in your region.

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and general notes on methods of test
   and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion (nominal conductor diameters
   from 0,250 mm up to and including 2,500 mm)
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Annex ZA (normative) - Normative references to international
         publications with their corresponding European
         publications

IEC 60317-8:2010 specifies the requirements of enamelled round copper winding wires of class 180 with a sole coating based on polyesterimide resin, which may be modified provided it retains the chemical identity of the original resin and meets all specified wire requirements. The main changes with respect to the previous edition are: - introduction of requirements for appearance; - new reference to resistance to refrigerants test method; - deletion of high temperature failure requirements; - introductin of pin hole test requirements.

Committee
CLC/TC 55
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Current

BS EN 60455-3-5:2006 Resin based reactive compounds used for electrical insulation Specifications for individual materials - Unsaturated polyester based impregnating resins
BS EN 60464-3-2:2002 Varnishes used for electrical insulation Requirements for hot curing impregnating varnishes
I.S. EN 60079-7:2015 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E'
I.S. EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS
EN IEC 60079-7:2015/A1:2018 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017)
EN 60464-3-2:2001/A1:2006 VARNISHES USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: HOT CURING IMPREGNATING VARNISHES
EN 60455-3-5:2006 Resin based reactive compounds used for electrical insulation - Part 3: Specifications for individual materials - Sheet 5: Unsaturated polyester based impregnating resins
I.S. EN 60464-3-2:2001 VARNISHES USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 2: HOT CURING IMPREGNATING VARNISHES
BS EN 60079-7 : 2015 EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015)
BS EN 50019:2000 Electrical apparatus for potentially explosive atmospheres. Increased safety \'e\'
I.S. EN 50020:2002 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INTRINSIC SAFETY "I"
I.S. EN 60079-11:2012 EXPLOSIVE ATMOSPHERES - PART 11: EQUIPMENT PROTECTION BY INTRINSIC SAFETY 'I'
BS EN 61858-1:2014 Electrical insulation systems. Thermal evaluation of modifications to an established electrical insulation system (EIS) Wire-wound winding EIS
BS EN 61858:2008 Electrical insulation systems. Thermal evaluation of modifications to an established wire-wound EIS
UNE-EN 60079-11:2013 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
EN 50020:2002 Electrical apparatus for potentially explosive atmospheres - Intrinsic safety 'i'
BS EN 50020:2002 Electrical apparatus for potentially explosive atmospheres. Intrinsic safety \'i\'
I.S. EN 60455-3-5:2006 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 5: UNSATURATED POLYESTER BASED IMPREGNATING RESINS
I.S. EN 61858-1:2014 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS
BS EN 60079-11:2012 Explosive atmospheres Equipment protection by intrinsic safety \'i\'
CEI EN 60455-3-5 : 2006 RESIN BASED REACTIVE COMPOUNDS USED FOR ELECTRICAL INSULATION - PART 3: SPECIFICATIONS FOR INDIVIDUAL MATERIALS - SHEET 5: UNSATURATED POLYESTER BASED IMPREGNATING RESINS
UNE-EN 60079-7:2016 Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
I.S. EN 50019:2001 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY "E"
EN 61858-1:2014 Electrical insulation systems - Thermal evaluation of modifications to an established electrical insulation system (EIS) - Part 1: Wire-wound winding EIS
EN 60079-11:2012 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
EN 50019:2000/corrigendum Apr. 2003 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY "E"
EN 61858:2008 ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED WIRE-WOUND EIS

EN 60317-0-1:2014 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
IEC 60317-0-1:2013 Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
EN 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties
IEC 60851-4:2016 Winding wires - Test methods - Part 4: Chemical properties

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.