EN 60352-4:1994/A1:2000
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
Amendment of
Superseded date
20-08-2020
Superseded by
Published date
12-01-2013
Sorry this product is not available in your region.
FOREWORD
INTRODUCTION
SECTION 1: GENERAL
1 Scope
2 Object
3 Normative references
4 Definitions
5 IEC type designation
SECTION 2: REQUIREMENTS
6 Workmanship
7 Tools
8 Insulation displacement termination (ID termination)
9 Wires
10 Non-accessible insulation displacement connections
(ID connections)
SECTION 3: TESTS
11 Testing
12 Type tests
13 Test schedules
SECTION 4: PRACTICAL GUIDANCE
14 General
15 Tool information
16 Termination information
17 Wire information
18 Connection information
19 ID connections, open housing design
20 ID connections, closed housing design
21 General additional information about ID connections
as part of a multi-pole connector
22 Final remarks
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Applies to non-accessible ID connections for which the tests and measurements of Section 3 are suitable and which are made with: - appropriately designed ID terminations; - wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter; - wires having stranded conductors of 0,05 square meter to 10 square meter cross-section; for use in telecommunication equipment and in electronic devices employing similar techniques.
| Committee |
SR 48B
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 60352-4 : 2001 | Identical |
| NBN EN 60352-4 : 1996 AMD 1 2001 | Identical |
| DIN EN 60352-4:2001-09 | Identical |
| I.S. EN 60352-4:1996 | Identical |
| BS EN 60352-4:1995 | Identical |
| PN EN 60352-4 : 2004 | Identical |
| NEN EN IEC 60352-4 : 1995 AMD 1 2001 | Identical |
| SN EN 60352-4 : 1994 AMD 1 2000 | Identical |
| CEI EN 60352-4/A1:2001 | Identical |
| NEN 10352-4 : 1995 | Identical |
| 09/30208429 DC : 0 | BS EN 50467 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| BS EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high-speed data applications Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| UNE-EN 50467:2012 | Railway applications - Rolling stock - Electrical connectors, requirements and test methods |
| I.S. EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 62852:2015 | CONNECTORS FOR DC-APPLICATION IN PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| BS EN 50548 : 2011 | JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| I.S. EN 50548:2011 | JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| EN 61076-3-101:1997 | Connectors with assessed quality, for use in d.c. low-frequency analogue and in digital high-speed data applications - Part 3: Rectangular connectors - Section 101: Detail specification for a range of shielded connectors with trapezoidal shaped shells and non-removable rectangular contacts on a 1,27 mm x 2,54 mm centre-line |
| EN 61076-4-110:2002 | Connectors for electronic equipment - Part 4-110: Printed board connectors with assessed quality - Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function |
| I.S. EN 61076-4:1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION - PRINTED BOARD CONNECTORS |
| 12/30235292 DC : 0 | BS EN 50343 - RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| BS EN 61076-3-101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE |
| CEI EN 61076-4-110 : 2003 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION |
| CEI EN 50467 : 2013 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| PREN 50467 : DRAFT 2009 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 60603-2:1998 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES |
| I.S. EN 60947-7-4:2013 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013 (EQV)) |
| CEI EN 50343 : 2015 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| BS EN 60603-7 : 2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS |
| UNE-EN 62852:2015 | Connectors for DC-application in photovoltaic systems - Safety requirements and tests |
| EN 60603-7:2009/A1:2011 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008/A1:2011) |
| BS EN 62790:2015 | Junction boxes for photovoltaic modules. Safety requirements and tests |
| 09/30214460 DC : 0 | BS EN 50548 - JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| CEI EN 61076-4 : 1997 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION PRINTED BOARD CONNECTORS |
| DD CLC/TS 50467:2008 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| I.S. EN 50173-1:2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| BS EN 50343 : 2014 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| BS EN 61076-4-105:1998 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication and audio industry |
| 01/637057 DC : DRAFT AUG 2001 | DRAFT EN 50173 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS |
| EN IEC 61076-2-111:2018 | Connectors for electrical and electronic equipment - Product requirements - Part 2-111: Circular connectors - Detail specification for power connectors with M12 screw-locking |
| BS EN 50173-1:2011 | Information technology. Generic cabling systems General requirements |
| EN 50173-1:2011 | Information technology - Generic cabling systems - Part 1: General requirements |
| NF EN 61076 3 101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTER-LINE |
| I.S. EN 61076-3-104:2017 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ |
| I.S. EN 61984:2009 | CONNECTORS - SAFETY REQUIREMENTS AND TESTS |
| S.R. CLC/TS 50467:2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| UNE-EN 50521:2010 | Connectors for photovoltaic systems - Safety requirements and tests |
| EN 62790:2015 | Junction boxes for photovoltaic modules - Safety requirements and tests |
| EN 61076-4:1996 | Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors |
| CEI EN 60947-7-4 : 2014 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS |
| BS EN 60603-2:1998 | Connectors for frequencies below 3 MHz for use with printed boards Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features |
| CEI EN 61076-3-101 : 1998 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D/C/ LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE |
| UNE-EN 60947-7-4:2014 | Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors |
| BS EN 61076-4-110:2002 | Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function |
| NF EN 61076 4 105 : 1999 | CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 105: DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION AND AUDIO INDUSTRY |
| CEI EN 50173-1 : 2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS |
| I.S. EN 60603-7:2009 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008) |
| I.S. EN 61076-4-110:2002 | CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION |
| BS EN 60947-7-4:2013 | Low-voltage switchgear and controlgear Ancillary equipment. PCB terminal blocks for copper conductors |
| UNE-EN 62790:2015 | Junction boxes for photovoltaic modules - Safety requirements and tests |
| I.S. EN 50343:2014 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| BS EN 61984:2009 | Connectors. Safety requirements and tests |
| EN 62852:2015 | Connectors for DC-application in photovoltaic systems - Safety requirements and tests |
| BS EN 50521 : 2009 | CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| 08/30179116 DC : DRAFT MAR 2008 | BS EN 50521 - CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| CLC/TS 50467 : 2008 COR 2008 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| BS EN 61076-4-107:2001 | Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| BS EN 50467:2011 | Railway applications. Rolling stock. Electrical connectors, requirements and test methods |
| BS EN 61076-3-104:2017 | Connectors for electrical and electronic equipment. Product requirements Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz |
| I.S. EN 50521:2008 | CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| UNE-EN 50548:2012 | Junction boxes for photovoltaic modules |
| I.S. EN IEC 61076-2-111:2018 | CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-111: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR POWER CONNECTORS WITH M12 SCREW-LOCKING |
| PREN 50548 : DRAFT 2009 | JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| EN 61076-3-104:2017 | Connectors for electrical and electronic equipment - Product requirements - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz |
| EN 50548 : 2011 AMD 2 2014 | JUNCTION BOXES FOR PHOTOVOLTAIC MODULES |
| EN 60603-2:1998/A1:2005 | CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES |
| EN 50521:2008/A1:2012 | CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS |
| EN 61984:2009 | Connectors - Safety requirements and tests |
| EN 61076-4-107:2001 | Connectors for electronic equipment - Part 4-107: Printed board connectors with assessed quality - Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations |
| EN 61076-3-100:2000 | Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 3-100: Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row |
| EN 50467:2011 | RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS |
| EN 50343 : 2014 AMD 1 2017 | RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING |
| EN 60947-7-4 : 2013 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013) |
| IEC GUIDE 109:2012 | Environmental aspects - Inclusion in electrotechnical product standards |
| IEC 60352-3:1993 | Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60512-6:1984 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 6: Climatic tests and soldering tests |
| IEC 60068-2-60:2015 RLV | Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test |
| EN 60352-3:1994 | Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| ISO 1463:2003 | Metallic and oxide coatings Measurement of coating thickness Microscopical method |
| EN 60512-1:2001 | Connectors for electronic equipment - Tests and measurements - Part 1: General |
| EN 60512-11-7:2003 | Connectors for electronic equipment - Tests and measurements - Part 11- 7: Climatic tests - Test 11g: Flowing mixed gas corrosion test |
| IEC 60512-11-7:2003 | Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test |
| IEC 60512-4:1976 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 4: Dynamic stress tests |
| IEC 60512-5:1992 | Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests |
| IEC 60512-1:2001 | Connectors for electronic equipment - Tests and measurements - Part 1: General |
| IEC 60050-581:2008 | International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment |
| IEC 60189-3:2007 | Low-frequency cables and wires with PVC insulation and PVC sheath - Part 3: Equipment wires with solid or stranded conductor wires, PVC insulated, in singles, pairs and triples |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.