EN 61315:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Calibration of fibre-optic power meters
05-02-2022
31-01-2006
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation for calibration
4.1 Organization
4.2 Traceability
4.3 Advice for measurements and calibrations
4.4 Recommendations to customers
5 Absolute power calibration
5.1 Establishing the calibration conditions
5.2 Calibration procedure
5.3 Calibration uncertainty
5.4 Reporting the results
6 Measurement uncertainty of a calibrated power meter
6.1 Uncertainty at reference conditions
6.2 Uncertainty at operating conditions
7 Nonlinearity calibration
7.1 Nonlinearity calibration based on superposition
7.2 Nonlinearity calibration based on comparison
with a calibrated power meter
7.3 Nonlinearity calibration based on comparison
with an attenuator
7.4 Calibration of power meter for high power
measurement
Annex A (normative) Mathematical basis
Bibliography
This international standard is applicable to instruments measuring radiant power emitted from sources which are typical for the fibre-optic communications industry. The standard describes the calibration of power meters to be performed by calibration laboratories or by power meter manufacturers.
| Committee |
CLC/SR 86
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNE-EN 61315:2006 | Identical |
| NF EN 61315 : 2006 | Identical |
| SN EN 61315 : 2006 | Identical |
| BS EN 61315:2006 | Identical |
| CEI EN 61315 : 2007 | Identical |
| I.S. EN 61315:2006 | Identical |
| NEN EN IEC 61315 : 2006 | Identical |
| IEC 61315:2005 | Identical |
| NBN EN 61315 : 2007 | Identical |
| DIN EN 61315:2006-09 | Identical |
| OVE/ONORM EN 61315 : 2006 | Identical |
| PN EN 61315 : 2006 | Identical |
| PNE-prEN 61315 | Identical |
| BS EN 62150-1:2005 | Fibre optic active components and devices. Test and measurement procedures General and guidance |
| BS EN 61300-1:2016 | Fibre optic interconnecting devices and passive components. Basic test and measurement procedures General and guidance |
| I.S. EN 61280-4-2:2014 | FIBRE-OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-2: INSTALLED CABLE PLANT - SINGLE-MODE ATTENUATION AND OPTICAL RETURN LOSS MEASUREMENT |
| EN 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| EN 61280-4-1:2009 | FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT |
| EN 62007-2:2009 | Semiconductor optoelectronic devices for fibre optic system applications - Part 2: Measuring methods |
| EN 62129-1:2016 | Calibration of wavelength/optical frequency measurement instruments - Part 1: Optical spectrum analyzers |
| EN 62129-2 : 2011 | CALIBRATION OF WAVELENGTH/OPTICAL FREQUENCY MEASUREMENT INSTRUMENTS - PART 2: MICHELSON INTERFEROMETER SINGLE WAVELENGTH METERS |
| CEI EN 62150-1 : 2005 | FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES - TEST AND MEASUREMENT PROCEDURES - PART 1: GENERAL AND GUIDANCE |
| BS EN 62129-1:2016 | Calibration of wavelength/optical frequency measurement instruments Optical spectrum analyzers |
| BS EN 61280-1-1:2013 | Fibre optic communication subsystem basic test procedures Test procedures for general communication subsystems. Transmitter output optical power measurement for single-mode optical fibre cable |
| CEI EN 62129-2 : 2012 | CALIBRATION OF WAVELENGTH/OPTICAL FREQUENCY MEASUREMENT INSTRUMENTS - PART 2: MICHELSON INTERFEROMETER SINGLE WAVELENGTH METERS |
| I.S. EN 62129-2:2011 | CALIBRATION OF WAVELENGTH/OPTICAL FREQUENCY MEASUREMENT INSTRUMENTS - PART 2: MICHELSON INTERFEROMETER SINGLE WAVELENGTH METERS |
| BS EN 61280-4-2:2014 | Fibre-optic communication subsystem test procedures Installed cable plant. Single-mode attenuation and optical return loss measurement |
| CEI EN 61280-4-1 : 2011 | FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT |
| CEI EN 61280-4-2 : 2015 | FIBRE-OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-2: INSTALLED CABLE PLANT - SINGLE-MODE ATTENUATION AND OPTICAL RETURN LOSS MEASUREMENT |
| CEI EN 61280-1-1 : 2014 | FIBRE OPTIC COMMUNICATION SUBSYSTEM BASIC TEST PROCEDURES - PART 1-1: TEST PROCEDURES FOR GENERAL COMMUNICATION SUBSYSTEMS - TRANSMITTER OUTPUT OPTICAL POWER MEASUREMENT FOR SINGLE-MODE OPTICAL FIBRE CABLE |
| I.S. EN 61300-1:2016 | FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS - BASIC TEST AND MEASUREMENT PROCEDURES - PART 1: GENERAL AND GUIDANCE |
| BS EN 62129-2:2011 | Calibration of wavelength/optical frequency measurement instruments Michelson interferometer single wavelength meters |
| BS EN 61280-4-1:2009 | Fibre optic communication subsystem test procedures Installed cable plant. Multimode attenuation measurement |
| BS EN 62150-2:2011 | Fibre optic active components and devices. Test and measurement procedures ATM-PON transceivers |
| BS EN 62522:2014 | Calibration of tuneable laser sources |
| BS EN 62007-2:2009 | Semiconductor optoelectronic devices for fibre optic system applications Measuring methods |
| I.S. EN 61280-4-1:2009 | FIBRE OPTIC COMMUNICATION SUBSYSTEM TEST PROCEDURES - PART 4-1: INSTALLED CABLE PLANT - MULTIMODE ATTENUATION MEASUREMENT |
| I.S. EN 61280-1-1:2013 | FIBRE OPTIC COMMUNICATION SUBSYSTEM BASIC TEST PROCEDURES - PART 1-1: TEST PROCEDURES FOR GENERAL COMMUNICATION SUBSYSTEMS - TRANSMITTER OUTPUT OPTICAL POWER MEASUREMENT FOR SINGLEMODE OPTICAL FIBRE CABLE (IEC 61280-1-1:2013 (EQV)) |
| I.S. EN 62150-1:2005 | FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES - TEST AND MEASUREMENT PROCEDURES - PART 1: GENERAL AND GUIDANCE |
| GS QKD 011 : 1.1.1 | QUANTUM KEY DISTRIBUTION (QKD); COMPONENT CHARACTERIZATION: CHARACTERIZING OPTICAL COMPONENTS FOR QKD SYSTEMS |
| UNE-EN 61300-1:2017 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 1: General and guidance |
| EN 62150-2:2011 | Fibre optic active components and devices - Test and measurement procedures - Part 2: ATM-PON transceivers |
| EN 61300-1:2016 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 1: General and guidance |
| EN 61280-1-1:2013 | Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable |
| EN 62150-1:2005 | Fibre optic active components and devices - Test and measurement procedures - Part 1: General and guidance |
| EN 62522:2014 | Calibration of tuneable laser sources |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
| IEC 60050-731:1991 | International Electrotechnical Vocabulary (IEV) - Part 731: Optical fibre communication |
| IEC 60793-2:2015 | Optical fibres - Part 2: Product specifications - General |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC TR 61930:1998 | Fibre optic graphical symbology |
| IEC TR 61931:1998 | Fibre optic - Terminology |
| IEC 61300-3-12:1997 | Fibre optic interconnecting devices and passive components - Basictest and measurement procedures - Part 3-12: Examinations andmeasurements - Polarization dependence of attenuation of asingle-mode fibre optic component: Matrix calculation method |
| IEC 60359:2001 | Electrical and electronic measurement equipment - Expression of performance |
| IEC 60050-300:2001 | International Electrotechnical Vocabulary (IEV) - Part 300: Electrical and electronic measurements and measuring instruments - Part 311: General terms relating to measurements - Part 312: General terms relating to electrical measurements - Part 313: Types of electrical measuring instruments - Part 314: Specific terms according to the type of instrument |
| IEC 61040:1990 | Power and energy measuring detectors, instruments and equipment for laser radiation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.