EN ISO 13628-5:2009
Current
The latest, up-to-date edition.
Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals (ISO 13628-5:2009)
15-12-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, abbreviated terms and definitions
4 Functional requirements
5 Safety, design and testing philosophy
6 Design requirements
7 Component design, manufacture and test
8 Terminations and ancillary equipment design
9 Umbilical design
10 Umbilical manufacture and test
11 Factory acceptance tests
12 Storage
13 Pre-installation activity
14 Load-out
15 Installation operations
Annex A (informative) - Information that should be provided
in a purchaser's functional specification
Annex B (informative) - Umbilical testing
Annex C (informative) - Hose and tube preferred sizes
Annex D (normative) - Characterization tests for hoses and
umbilicals
Annex E (informative) - Fatigue testing
Annex F (informative) - Load-effect analysis
Annex G (informative) - Umbilical full-scale tests
Annex H (informative) - Tube material matrix
Annex I (informative) - Tube-wall thickness example
calculation
Annex J (informative) - Buckling of metallic tubes
Bibliography
ISO 13628-5:2009 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary equipment for the petroleum and natural gas industries. Ancillary equipment does not include top side hardware. Topside hardware refers to any hardware that is not permanently attached to the umbilical, above the topside hang-off termination.ISO 13628-5:2009 applies to umbilicals containing components, such as electrical cables, optical fibres, thermoplastic hoses and metallic tubes, either alone or in combination; and to umbilicals for static or dynamic service, with surface-surface, surface-subsea and subsea-subsea routings .ISO 13628-5:2009 does not apply to the associated component connectors, unless they affect the performance of the umbilical or that of its ancillary equipment.ISO 13628-5:2009 applies only to tubes with the following dimensions: wall thickness, t 6 mm, internal diameter, ID 50,8 mm (2 in). Tubular products greater than these dimensions can be regarded as pipe/linepipe and it is expected that they be designed and manufactured according to a recognised pipeline/linepipe standard.ISO 13628-5:2009 does not apply to a tube or hose rated lower than 7 MPa (1 015 psi), or to electric cable voltage ratings above standard rated voltages = 3,6/6(7,2) kV rms, where U0, U and Um are as defined in IEC 60502-1 and IEC 60502-2.
Committee |
CEN/TC 12
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Standards | Relationship |
BS EN ISO 13628-5:2009 | Identical |
NF EN ISO 13628-5 : 2013 | Identical |
NBN EN ISO 13628-5 : 2010 | Identical |
NS EN ISO 13628-5 : 2009 | Identical |
ISO 13628-5:2009 | Identical |
I.S. EN ISO 13628-5:2009 | Identical |
SN EN ISO 13628-5 : 2010 | Identical |
PN EN ISO 13628-5 : 2010 | Identical |
DIN EN ISO 13628-5:2010-05 | Identical |
NEN EN ISO 13628-5 : 2010 | Identical |
UNE-EN ISO 13628-5:2009 | Identical |
UNI EN ISO 13628-5 : 2010 | Identical |
ASTM E 1001 : 2016 : REDLINE | Standard Practice for Detection and Evaluation of Discontinuities by the Immersed Pulse-Echo Ultrasonic Method Using Longitudinal Waves |
IEC 60038:2009 | IEC standard voltages |
IEC 60228:2004 | Conductors of insulated cables |
EN 10257-2:2011 | Zinc or zinc alloy coated non-alloy steel wire for armouring either power cables or telecommunication cables - Part 2: Submarine cables |
ASTM E 309 : 2016 : REDLINE | Standard Practice for Eddy Current Examination of Steel Tubular Products Using Magnetic Saturation |
IEC 60502-2:2014 RLV | Power cables with extruded insulation and their accessories for rated voltages from 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) up to 30 kV (<em>U</em><sub>m</sub> = 36 kV) – Part 2: Cables for rated voltages from 6 kV (<em>U</em><sub>m</sub> = 7,2 kV) up to 30 kV (<em>U</em><sub>m</sub> = 36 kV) |
ISO 13628-2:2006 | Petroleum and natural gas industries Design and operation of subsea production systems Part 2: Unbonded flexible pipe systems for subsea and marine applications |
ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
ISO 6801:1983 | Rubber or plastics hoses Determination of volumetric expansion |
IEC 60793-2:2015 | Optical fibres - Part 2: Product specifications - General |
ASTM E 562 : 2011 : REDLINE | Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count |
ISO 14732:2013 | Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials |
IEC 60502-1:2004+AMD1:2009 CSV | Power cables with extruded insulation and their accessories for rated voltages from 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) up to 30 kV(<em>U</em><sub>m</sub> = 36 kV) - Part 1: Cables for rated voltages of 1 kV (<em>U</em><sub>m</sub> = 1,2 kV) and 3 kV (<em>U</em><sub>m</sub> = 3,6 kV) |
ISO 4672:1997 | Rubber and plastics hoses Sub-ambient temperature flexibility tests |
ASTM E 384 : 2017 : REDLINE | Standard Test Method for Microindentation Hardness of Materials |
ASTM E 273 : 2015 : REDLINE | Standard Practice for Ultrasonic Testing of the Weld Zone of Welded Pipe and Tubing |
IEC 60794-1-2:2017 | Optical fibre cables - Part 1-2: Generic specification - Basic optical cable test procedures - General guidance |
ASME B31.3:2016 | PROCESS PIPING |
ISO 13628-11:2007 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 11: Flexible pipe systems for subsea and marine applications |
IEC 60794-1-1:2015 | Optical fibre cables - Part 1-1: Generic specification - General |
API SPEC 17J : 2014 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
API 2RD : 2013 | DYNAMIC RISERS FOR FLOATING PRODUCTION SYSTEMS |
ASTM E 426 : 2016 : REDLINE | Standard Practice for Electromagnetic (Eddy Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys |
ISO 8308:2015 | Rubber and plastics hoses and tubing Determination of transmission of liquids through hose and tubing walls |
EN 10204:2004 | Metallic products - Types of inspection documents |
API RP 17B : 2014 | RECOMMENDED PRACTICE FOR FLEXIBLE PIPE |
ISO 13628-6:2006 | Petroleum and natural gas industries Design and operation of subsea production systems Part 6: Subsea production control systems |
ASME PV CODE 5 : 2017 | BOILER AND PRESSURE VESSEL CODE - NONDESTRUCTIVE EXAMINATION |
ISO 7751:2016 | Rubber and plastics hoses and hose assemblies Ratios of proof and burst pressure to maximum working pressure |
API SPEC 17E : 2017 | SPECIFICATION FOR SUBSEA UMBILICALS |
ISO 13628-8:2002 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems |
ISO 1402:2009 | Rubber and plastics hoses and hose assemblies Hydrostatic testing |
ISO 4080:2009 | Rubber and plastics hoses and hose assemblies — Determination of permeability to gas |
ISO 6803:2017 | Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing |
ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
API RP 17I : 1996 | INSTALLATION GUIDELINES FOR SUBSEA UMBILICALS |
ASTM E 8/E8M : 2016-09 | TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS |
ASTM E 92 : 2017 : REDLINE | Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials |
EEMUA 194 : 2012 | GUIDELINES FOR MATERIALS SELECTION AND CORROSION CONTROL FOR SUBSEA OIL AND GAS PRODUCTION EQUIPMENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Logging out.