I.S. EN 1218-4:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 4: EDGE BANDING MACHINES FED BY CHAIN(S)
Hardcopy , PDF
28-09-2015
English
01-01-2004
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 General
3.2 Terms
3.3 Definitions
4 List of significant hazards
5 Safety requirements and/or measures
5.1 General
5.2 Controls
5.2.1 Safety and reliability of control systems
5.2.2 Position of controls
5.2.3 Starting
5.2.4 Stop controls
5.2.5 Emergency stop
5.2.6 Integrated feed
5.2.7 Mode selection
5.2.8 Speed changing
5.2.9 Control duplication
5.2.10 Failure of the power supply
5.2.11 Failure of the control circuits
5.3 Protection against mechanical hazards
5.3.1 Stability
5.3.2 Risk of break-up during operation
5.3.3 Tool holder and tool design
5.3.4 Braking
5.3.5 Devices to minimise the possibility or the effect of
ejection or kick-back
5.3.6 Work-piece supports and guides
5.3.7 Prevention of access to moving parts
5.4 Protection against non-mechanical hazards
5.4.1 Fire
5.4.2 Noise
5.4.3 Emission of chips, and dust
5.4.4 Electricity
5.4.5 Ergonomics and Handling
5.4.6 Lighting
5.4.7 Pneumatics
5.4.8 Hydraulics
5.4.9 Heat
5.4.10 Substances
5.4.11 Electromagnetic compatibility
5.4.12 Static Electricity
5.4.13 Errors of fitting
5.4.14 Isolation
5.4.15 Maintenance
6 Information for use
6.1 Warning devices
6.2 Marking
6.3 Instruction handbook
Annex A (informative) Examples of safety related control systems
Annex B (normative) Tool spindle dimensional tolerances
Annex ZA (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive 98/37/EC
Annex ZB (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive 2006/42/EC
Bibliography
Describes all the significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to edge banding machines fed by chain(s) where the loading and unloading is manual and where the maximum work-piece height capacity is 75 mm.
| DevelopmentNote |
2004 Edition Re-issued in August 2009 & incorporates AMD 2 2009. (08/2009)
|
| DocumentType |
Standard
|
| Pages |
54
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| Standards | Relationship |
| DIN EN 1218-4:2009-12 | Identical |
| UNI EN 1218-4 : 2009 | Identical |
| EN 1218-4:2004+A2:2009 | Identical |
| UNE-EN 1218-4:2005 | Identical |
| BS EN 1218-4 : 2004 | Identical |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.