I.S. EN 12392:2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ALUMINIUM AND ALUMINIUM ALLOYS - WROUGHT PRODUCTS AND CAST PRODUCTS - SPECIAL REQUIREMENTS FOR PRODUCTS INTENDED FOR THE PRODUCTION OF PRESSURE EQUIPMENT
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2016
Publisher
Superseded date
04-03-2023
Superseded by
€108.00
Excluding VAT
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Technical conditions for inspection and delivery
6 Mechanical properties
7 Tolerances on dimensions and form
Annex A (informative) - Materials and
application ranges
Annex B (informative) - Tensile properties at
low and high temperatures
Annex ZA (informative) - Relationship between
this European Standard and the Essential
safety requirements of Directive 2014/68/EU
aimed to be covered
Bibliography
Describes the material requirements and testing procedures applicable to wrought and cast aluminium and aluminium alloys intended for use in the production of pressure equipment.
| DocumentType |
Standard
|
| Pages |
84
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN 12392 : 2016 | Identical |
| NS EN 12392 : 2000 | Identical |
| NEN EN 12392 : 2016 | Identical |
| BS EN 12392:2016 | Identical |
| EN 12392:2016 | Identical |
| DIN EN 12392:2016-08 | Identical |
| NF EN 12392 : 2016 | Identical |
| ONORM EN 12392 : 2016 | Identical |
| UNE-EN 12392:2017 | Identical |
| ASTM B 234M : 2017 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Surface Condensers, Evaporators, and Heat Exchangers (Metric) |
| EN 13957:2008 | Aluminium and aluminium alloys - Extruded round, coiled tube for general applications - Specification |
| EN 485-1:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery |
| EN 755-1:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery |
| ISO 8496:2013 | Metallic materials — Tube — Ring tensile test |
| EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
| EN ISO 8493:2004 | Metallic materials - Tube - Drift-expanding test (ISO 8493:1998) |
| EN 754-3:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form |
| ISO 6506-1:2014 | Metallic materials — Brinell hardness test — Part 1: Test method |
| EN 754-7:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN 755-5:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form |
| EN 13445-5 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 5: INSPECTION AND TESTING |
| EN ISO 3452-1:2013 | Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, Corrected version 2014-05-01) |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 485-3:2003 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products |
| EN 755-9:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form |
| EN 4050-3:2012 | Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 3: Reference blocks |
| EN 485-4:1993 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products |
| EN ISO 8495:2013 | Metallic materials - Tube - Ring-expanding test (ISO 8495:2013) |
| EN 755-3:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 3: Round bars, tolerances on dimensions and form |
| EN ISO 8496:2013 | Metallic materials - Tube - Ring tensile test (ISO 8496:2013) |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| EN 4050-4:2012 | Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 4: Acceptance criteria |
| EN 755-8:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 755-4:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form |
| EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
| EN 4050-1:2012 | Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 1: General requirements |
| ISO 8493:1998 | Metallic materials — Tube — Drift-expanding test |
| EN 586-3:2001 | Aluminium and aluminium alloys - Forgings - Part 3: Tolerances on dimensions and form |
| EN 755-7:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN 13445-8 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 8: ADDITIONAL REQUIREMENTS FOR PRESSURE VESSELS OF ALUMINIUM AND ALUMINIUM ALLOYS |
| EN 754-6:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form |
| ISO 3452-1:2013 | Non-destructive testing — Penetrant testing — Part 1: General principles |
| EN 755-6:2008 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form |
| EN 12258-1:2012 | Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms |
| EN 1370:2011 | Founding - Examination of surface condition |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| EN 1371-1:2011 | Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings |
| EN 754-1:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery |
| EN 13958:2008 | Aluminium and aluminium alloys - Cold drawn, round, coiled tube for general applications - Specification |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| EN 2101:1991 | Aerospace series - Chromic acid anodizing of aluminium and wrought aluminium alloys |
| EN 941:2014 | Aluminium and aluminium alloys - Circle and circle stock for the production of general applications - Specifications |
| EN 754-5:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form |
| ISO 8495:2013 | Metallic materials — Tube — Ring-expanding test |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 586-1:1997 | Aluminium and aluminium alloys - Forgings - Part 1: Technical conditions for inspection and delivery |
| EN 754-8:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 13480-8:2017 | Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping |
| ISO 8492:2013 | Metallic materials — Tube — Flattening test |
| EN 12681:2003 | Founding - Radiographic examination |
| EN 754-2:2016 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties |
| EN ISO 8492:2013 | Metallic materials - Tube - Flattening test (ISO 8492:2013) |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| EN 14361:2004 | Aluminium and aluminium alloys - Chemical analysis - Sampling from metal melts |
| EN 1559-4:2015 | Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings |
| EN 13480-5:2017 | Metallic industrial piping - Part 5: Inspection and testing |
| EN 14726:2005 | Aluminium and aluminium alloys - Chemical analysis - Guideline for spark optical emission spectrometric analysis |
| EN 4050-2:2012 | Aerospace series - Test method for metallic materials - Ultrasonic inspection of bars, plates, forging stock and forgings - Part 2: Performance of test |
| EN 754-4:2008 | Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form |
| EN 755-2:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties |
| EN 12020-1:2008 | Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery |
| ISO 8062:1994 | Castings — System of dimensional tolerances and machining allowances |
| ASTM E 215 : 2016 : REDLINE | Standard Practice for Standardizing Equipment and Electromagnetic Examination of Seamless Aluminum-Alloy Tube |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.