I.S. EN 60706-2:2006
Current
The latest, up-to-date edition.
MAINTAINABILITY OF EQUIPMENT - PART 2: MAINTAINABILITY REQUIREMENTS AND STUDIES DURING THE DESIGN AND DEVELOPMENT PHASE
Hardcopy , PDF
English
01-01-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and acronyms
3.1 Terms and definitions
3.2 Acronyms
4 General approach
5 Principle of maintainability
6 Maintainability activities in the life cycle
6.1 General
6.2 Concept and definition phase
6.3 Design and development phase
6.4 Manufacture and installation phase
6.5 Operation and maintenance phases
6.6 Disposal phase
7 Specification of maintainability requirements
7.1 Statement of maintainability requirements
7.2 Maintainability characteristics
7.3 Constraints
7.4 Maintainability programme requirements
7.5 Verification
8 Maintainability studies in the design and development phase
8.1 General
8.2 Objectives
8.3 Maintainability studies in the design process
8.4 Analysis tools and procedures
9 Design support
9.1 Liaison
9.2 Design criteria and check-lists
9.3 Design reviews
Annex A (informative) Maintainability allocation
Annex B (informative) Example of a maintainability allocation
Annex C (informative) Example of allocation of reliability
values and maintenance strategy selection for a system
with non-constant failure rate
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Bibliography
Covers the maintainability requirements and related design and use parameter, and discusses some activities necessary to achieve the required maintainability characteristics and their relationship to planning of maintenance. It describes the general approach in reaching these objectives and shows how maintainability characteristics should be specified in a requirements document or contract.
DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
DocumentType |
Standard
|
Pages |
116
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Current
|
Standards | Relationship |
DIN EN 60706-2:2006-12 | Identical |
NF EN 60706-2 : 2006 | Identical |
IEC 60706-2:2006 | Identical |
BS EN 60706-2:2006 | Identical |
SN EN 60706-2 : 2006 | Identical |
NBN EN 60706-2 : 2006 | Identical |
EN 60706-2:2006 | Identical |
IEC 61025:2006 | Fault tree analysis (FTA) |
EN 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
IEC 60300-3-3:2017 | Dependability management - Part 3-3: Application guide - Life cycle costing |
IEC 61649:2008 | Weibull analysis |
IEC 60300-3-12:2011 | Dependability management - Part 3-12: Application guide - Integrated logistic support |
IEC 60300-3-14:2004 | Dependability management - Part 3-14: Application guide - Maintenance and maintenance support |
IEC 60706-3:2006 | Maintainability of equipment - Part 3: Verification and collection, analysis and presentation of data |
IEC 61160:2005 | Design review |
EN 60300-3-1:2004 | Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
EN 60300-3-12:2011 | Dependability management - Part 3-12: Application guide - Integrated logistic support |
EN 60300-3-14:2004 | Dependability management - Part 3-14: Application guide - Maintenance and maintenance support |
EN 60300-3-3:2017 | Dependability management - Part 3-3: Application guide - Life cycle costing |
IEC 60300-3-1:2003 | Dependability management - Part 3-1: Application guide - Analysis techniques for dependability - Guide on methodology |
IEC 60300-1:2014 | Dependability management - Part 1: Guidance for management and application |
HD 617 : 200S1 | FAULT TREE ANALYSIS (FTA) |
IEC 60300-3-11:2009 | Dependability management - Part 3-11: Application guide - Reliability centred maintenance |
IEC 60300-2:2004 | Dependability management - Part 2: Guidelines for dependability management |
IEC 60300-3-10:2001 | Dependability management - Part 3-10: Application guide - Maintainability |
IEC 60706-5:2007 | Maintainability of equipment - Part 5: Testability and diagnostic testing |
EN 61160:2005 | Design review |
IEC 61710:2013 | Power law model - Goodness-of-fit tests and estimation methods |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.