• I.S. EN 61189-5-503:2017

    Current The latest, up-to-date edition.

    TEST METHODS FOR ELECTRICAL MATERIALS, PRINTED BOARD AND OTHER INTERCONNECTION STRUCTURES AND ASSEMBLIES - PART 5-503: GENERAL TEST METHOD FOR MATERIALS AND ASSEMBLIES - CONDUCTIVE ANODIC FILAMENTS (CAF) TESTING OF CIRCUIT BOARDS

    Available format(s):  Hardcopy, PDF

    Language(s):  English

    Published date:  01-01-2017

    Publisher:  National Standards Authority of Ireland

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Dates of withdrawal of national standards are available from NSAI.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    National Foreword
    FOREWORD
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Testing condition
    5 Specimen
    6 Equipment/Apparatus or material
    7 Resistance measurement method
    8 Test method
    9 Procedure
    Annex A (informative) - Forms of electrochemical
            migration
    Bibliography
    Annex ZA (normative) - Normative references to
             international publications with their
             corresponding European publications

    Abstract - (Show below) - (Hide below)

    Defines the conductive anodic filament (hereafter referred to as CAF) and specifies not only the steady-state temperature and humidity test, but also a temperature-humidity cyclic test and an unsaturated pressurized vapour test (HAST).

    General Product Information - (Show below) - (Hide below)

    Development Note For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (09/2017)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Current

    Standards Referencing This Book - (Show below) - (Hide below)

    IEC 60721-1:1990+AMD1:1992+AMD2:1995 CSV Classification of environmental conditions - Part 1: Environmental parameters and their severities
    IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
    IEC TR 62866:2014 Electrochemical migration in printed wiring boards and assemblies - Mechanisms and testing
    EN 60068-1:2014 ENVIRONMENTAL TESTING - PART 1: GENERAL AND GUIDANCE (IEC 60068-1:2013)
    IEC 60068-2-66:1994 Environmental testing - Part 2: Test methods - Test Cx: Damp heat, steady state (unsaturated pressurized vapour)
    IPC TM 650 : 0 TEST METHODS MANUAL
    IEC 60068-2-67:1995 Environmental testing - Part 2-67: Tests - Test Cy: Damp heat, steady state, accelerated test primarily intended for components
    IEC 60068-2-38:2009 Environmental testing - Part 2-38: Tests - Test Z/AD: Composite temperature/humidity cyclic test
    IEC 60721-2-1:2013 Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity
    IPC 9691 : A USER GUIDE FOR THE IPC-TM-650, METHOD 2.6.25, CONDUCTIVE ANODIC FILAMENT (CAF) RESISTANCE AND OTHER INTERNAL ELECTROCHEMICAL MIGRATION TESTING
    IEC 60068-3-5:2001 Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers
    EN 60068-2-38:2009 ENVIRONMENTAL TESTING - PART 2-38: TESTS - TEST Z/AD: COMPOSITE TEMPERATURE/HUMIDITY CYCLIC TEST
    IEC 60721-3-0:1984+AMD1:1987 CSV Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Introduction
    IEC 60194:2015 Printed board design, manufacture and assembly - Terms and definitions
    EN 60068-2-67:1996 ENVIRONMENTAL TESTING - TESTS - TEST CY: DAMP HEAT, STEADY STATE, ACCELERATED TEST PRIMARILY INTENDED FOR COMPONENTS
    EN 60068-2-78:2013 ENVIRONMENTAL TESTING - PART 2-78: TESTS - TEST CAB: DAMP HEAT, STEADY STATE (IEC 60068-2-78:2012)
    ASTM D 257 : 2014 : REDLINE Standard Test Methods for DC Resistance or Conductance of Insulating Materials
    EN 60068-2-66:1994 ENVIRONMENTAL TESTING - PART 2: TEST METHODS - TEST CX: DAMP HEAT, STEADY STATE (UNSATURATED PRESSURIZED VAPOUR)
    IEC 60068-3-4:2001 Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests
    EN 60068-2-30:2005 ENVIRONMENTAL TESTING - PART 2-30: TESTS - TEST DB: DAMP HEAT, CYCLIC (12 H + 12 H CYCLE)
    IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective