I.S. EN 61858-1:2014
Current
The latest, up-to-date edition.
ELECTRICAL INSULATION SYSTEMS - THERMAL EVALUATION OF MODIFICATIONS TO AN ESTABLISHED ELECTRICAL INSULATION SYSTEM (EIS) - PART 1: WIRE-WOUND WINDING EIS
Hardcopy , PDF
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General considerations
5 Substitution of phase or ground insulation
6 Substitution of winding wire
7 Substitution of impregnating resin/varnish
8 Substitution with other EIM
9 Evaluation of additions
10 Chemical compatibility of a combination of materials
11 Single-point thermal ageing test (procedure C)
12 Full thermal aging test (procedure D)
Annex A (normative) - Classes of winding wire
Annex B (informative) - Visual representations of coils
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Defines the required test procedures for qualification of modifications of an established electrical insulation system (EIS) with respect to its thermal classification.
DevelopmentNote |
Supersedes I.S. EN 61858. (08/2014) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
DocumentType |
Standard
|
Pages |
76
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Current
|
Supersedes |
Standards | Relationship |
EN 61858-1:2014 | Identical |
IEC 60317-35:2013 | Specifications for particular types of winding wires - Part 35: Solderable polyurethane enamelled round copper wire, class 155, with a bonding layer |
IEC 60317-3:2004+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 3: Polyester enamelled round copper wire, class 155 |
EN 60317-34 : 1997 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - POLYESTER ENAMELLED ROUND COPPER WIRE, CLASS 130 |
IEC 60317-42:1997+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 42: Polyester-amide-imide enamelled round copper wire, class 200 |
EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
EN 60317-50 : 2012 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 50: GLASS-FIBRE WOUND SILICONE RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE, TEMPERATURE INDEX 200 |
IEC 60317-50:2012 | Specifications for particular types of winding wires - Part 50: Glass-fibre wound silicone resin or varnish impregnated, bare or enamelled round copper wire, temperature index 200 |
IEC 60317-15:2004+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 15: Polyesterimide enamelled round aluminium wire, class 180 |
IEC 60317-12:2010 | Specifications for particular types of winding wires - Part 12: Polyvinyl acetal enamelled round copper wire, class 120 |
IEC 60317-51:2014 | Specifications for particular types of winding wires - Part 51: Solderable polyurethane enamelled round copper wire, class 180 |
IEC 60317-4:2015 | Specifications for particular types of winding wires - Part 4: Solderable polyurethane enamelled round copper wire, class 130 |
IEC 60317-21:2013 | Specifications for particular types of winding wires - Part 21: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 155 |
IEC 60317-57:2010 | Specifications for particular types of winding wires - Part 57: Polyamide-imide enameled round copper wire, class 220 |
IEC 60317-19:1990+AMD1:1997+AMD2:1999 CSV | Specifications for particular types of winding wires - Part 19: Solderable polyurethane enamelled round copper wire, overcoated with polyamide, class 130 |
EN 61857-21:2009 | ELECTRICAL INSULATION SYSTEMS - PROCEDURES FOR THERMAL EVALUATION - PART 21: SPECIFIC REQUIREMENTS FOR GENERAL-PURPOSE MODELS - WIRE-WOUND APPLICATIONS |
IEC 60317-8:2010 | Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180 |
IEC 61857-21:2009 | Electrical insulation systems - Procedures for thermal evaluation - Part 21: Specific requirements for general-purpose models - Wire-wound applications |
EN 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
EN 60317-46:2014 | Specifications for particular types of winding wires - Part 46: Aromatic polyimide enamelled round copper wire, class 240 |
IEC 60317-34:1997 | Specifications for particular types of winding wires - Part 34: Polyester enamelled round copper wire, class 130L |
IEC 60505:2011 | Evaluation and qualification of electrical insulation systems |
EN 60317-12:2010 | Specifications for particular types of winding wires - Part 12: Polyvinyl acetal enamelled round copper wire, class 120 |
IEC 62317-2:2010 | Ferrite cores - Dimensions - Part 2: Pot-cores for use in telecommunications, power supply, and filter applications |
IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
IEC 60317-23:2013 | Specifications for particular types of winding wires - Part 23: Solderable polyesterimide enamelled round copper wire, class 180 |
IEC 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
IEC 61857-1:2008 | Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage |
EN 60317-21:2014 | Specifications for particular types of winding wires - Part 21: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 155 |
EN 60317-13:2010 | Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200 |
EN 61033 : 2006 | TEST METHODS FOR THE DETERMINATION OF BOND STRENGTH OF IMPREGNATING AGENTS TO AN ENAMELLED WIRE SUBSTRATE |
IEC 60317-38:2013 | Specifications for particular types of winding wires - Part 38: Polyester or polyesterimide overcoated with polyamide-imide, enamelled round copper wire, class 200, with a bonding layer |
IEC 60317-37:2013 | Specifications for particular types of winding wires - Part 37: Polyesterimide enamelled round copper wire, class 180, with a bonding layer |
EN 60317-19:1995/A2:2000 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 19: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE OVERCOATED WITH POLYAMIDE, CLASS 130 |
EN 60317-53:2014 | Specifications for particular types of winding wires - Part 53: Aromatic polyamide (aramid) tape wrapped rectangular copper wire, temperature index 220 |
IEC 60317-13:2010 | Specifications for particular types of winding wires - Part 13: Polyester or polyesterimide overcoated with polyamide-imide enamelled round copper wire, class 200 |
EN 60317-35:2014 | Specifications for particular types of winding wires - Part 35: Solderable polyurethane enamelled round copper wire, class 155, with a bonding layer |
EN 60317-48:2012 | Specifications for particular types of winding wires - Part 48: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155 |
IEC 60317-2:2012 | Specifications for particular types of winding wires - Part 2: Solderable polyurethane enamelled round copper wire, class 130, with a bonding layer |
EN 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
EN 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
IEC 60317-36:2013 | Specifications for particular types of winding wires - Part 36: Solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer |
EN 60317-2:2012 | Specifications for particular types of winding wires - Part 2: Solderable polyurethane enamelled round copper wire, class 130, with a bonding layer |
IEC 60317-53:2014 | Specifications for particular types of winding wires - Part 53: Aromatic polyamide (aramid) tape wrapped rectangular copper wire, temperature index 220 |
IEC 60317-20:2013 | Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155 |
IEC 60034-18-21:2012 | Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification |
IEC 60317-48:2012 | Specifications for particular types of winding wires - Part 48: Glass-fibre wound resin or varnish impregnated, bare or enamelled round copper wire, temperature index 155 |
IEC 60317-1:2010 | Specifications for particular types of winding wires - Part 1: Polyvinyl acetal enamelled round copper wire, class 105 |
EN 60317-43:1997/A1:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 43: AROMATIC POLYIMIDE TAPE WRAPPED ROUND COPPER WIRE, CLASS 240 |
IEC 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
EN 60317-38:2014 | Specifications for particular types of winding wires - Part 38: Polyester or polyesterimide overcoated with polyamide-imide, enamelled round copper wire, class 200, with a bonding layer |
IEC 60317-22:2004+AMD1:2009 CSV | Specifications for particular types of winding wires - Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 |
EN 62317-2:2010/corrigendum:2010 | FERRITE CORES - DIMENSIONS - PART 2: POT-CORES FOR USE IN TELECOMMUNICATIONS, POWER SUPPLY, AND FILTER APPLICATIONS |
EN 60317-20:2014 | Specifications for particular types of winding wires - Part 20: Solderable polyurethane enamelled round copper wire, class 155 |
IEC 60317-46:2013 | Specifications for particular types of winding wires - Part 46: Aromatic polyimide enamelled round copper wire, class 240 |
EN 60317-8:2010 | Specifications for particular types of winding wires - Part 8: Polyesterimide enamelled round copper wire, class 180 |
EN 60317-22:2004/A1:2010 | Specifications for particular types of winding wires - Part 22: Polyester or polyesterimide enamelled round copper wire overcoated with polyamide, class 180 |
EN 60317-55:2014 | Specifications for particular types of winding wires - Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, Class 180 |
IEC 60317-55:2013 | Specifications for particular types of winding wires - Part 55: Solderable polyurethane enamelled round copper wire overcoated with polyamide, class 180 |
IEC 60317-43:1997+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 43: Aromatic polyimide type wrapped round copper wire, class 240 |
IEC 60216-5:2008 | Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material |
EN 60317-23:2014 | Specifications for particular types of winding wires - Part 23: Solderable polyesterimide enamelled round copper wire, class 180 |
EN 60317-36:2014 | Specifications for particular types of winding wires - Part 36: Solderable polyesterimide enamelled round copper wire, class 180, with a bonding layer |
EN 60505:2011/AC:2017-03 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS (IEC 60505:2011/COR1:2017) |
EN 60317-42:1997/A1:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 42: POLYESTER-AMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200 |
IEC 60317-54:2001 | Specifications for particular types of winding wires - Part 54: Polyester enamelled round copper wire, class 155L |
EN 60317-26:1996/A2:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 26: POLYAMIDE-IMIDE ENAMELLED ROUND COPPER WIRE, CLASS 200 |
IEC 61033:1991 | Test methods for the determination of bond strength of impregnating agents to an enamelled wire substrate |
EN 60317-37:2014 | Specifications for particular types of winding wires - Part 37: Polyesterimide enamelled round copper wire, class 180, with a bonding layer |
EN 60317-51:2014 | Specifications for particular types of winding wires - Part 51: Solderable polyurethane enamelled round copper wire, class 180 |
EN 61857-1:2009 | Electrical insulation systems - Procedures for thermal evaluation - Part 1: General requirements - Low-voltage |
EN 60317-4:1994/A2:2000 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 4: SOLDERABLE POLYURETHANE ENAMELLED ROUND COPPER WIRE, CLASS 130 |
EN 60317-57:2010 | Specifications for particular types of winding wires - Part 57: Polyamide-imide enamelled round copper wire, class 220 |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.