I.S. EN 62282-2:2012
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
FUEL CELL TECHNOLOGIES - PART 2: FUEL CELL MODULES (IEC 62282-2:2012 (EQV))
Hardcopy , PDF
11-06-2023
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Type tests
6 Routine tests
7 Markings and instructions
Annex A (informative) - Additional information for the
performance and evaluation of the tests
Annex B (informative) - List of notes concerning particular
conditions in certain countries
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Gives the minimum requirements for safety and performance of fuel cell modules and pertains to fuel cell modules with the following electrolyte chemistry: - alkaline; - polymer electrolyte (including direct methanol fuel cells); - phosphoric acid; - molten carbonate; - solid oxide; - aqueous solution of salts.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
46
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 62282-2 : 2012 | Identical |
| DIN EN 62282-2 : 2013 | Identical |
| EN 62282-2:2012 | Identical |
| BS EN 62282-2:2012 | Identical |
| NBN EN 62282-2 : 2012 | Identical |
| UNE-EN 62282-2:2012 | Identical |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| EN 62040-1:2008/A1:2013 | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: GENERAL AND SAFETY REQUIREMENTS FOR UPS (IEC 62040-1:2008/A1:2013) |
| CSA B51 : 2014 | BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC TS 62282-1:2013 | Fuel cell technologies - Part 1: Terminology |
| ISO 4672:1997 | Rubber and plastics hoses Sub-ambient temperature flexibility tests |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| IEC 60079-20-1:2010 | Explosive atmospheres - Part 20-1: Material characteristics for gas and vapour classification - Test methods and data |
| IEC 62040-1:2017 EXV | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS |
| CGA 12.6 : M94(R1999) | VEHICLE REFUELLING APPLIANCES |
| EN 50178:1997 | Electronic equipment for use in power installations |
| CSA C22.2 No. 60529 : 2016 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) |
| SAE J1739_200901 | Potential Failure Mode and Effects Analysis in Design (Design FMEA), Potential Failure Mode and Effects Analysis in Manufacturing and Assembly Processes (Process FMEA) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 62282-3-100:2012 | Fuel cell technologies - Part 3-100: Stationary fuel cell power systems - Safety |
| EN 62061:2005/A2:2015 | SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015) |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 1402:2009 | Rubber and plastics hoses and hose assemblies Hydrostatic testing |
| ISO 1307:2006 | Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| ISO 1436:2017 | Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 23550:2011 | Safety and control devices for gas burners and gas-burning appliances General requirements |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.