I.S. EN ISO 10350-1:2017
Current
Current
The latest, up-to-date edition.
PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017)
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2017
Publisher
€28.00
Excluding VAT
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
National Foreword
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specimen preparation and conditioning
5 Test requirements
6 Presentation of results
Bibliography
Describes specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics.
| DevelopmentNote |
Supersedes I.S. EN ISO 10350. (10/2006)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| BS EN ISO 10350-1 : 2008 | Identical |
| EN ISO 10350-1:2017 | Identical |
| DIN EN ISO 10350-1:2016-08 (Draft) | Identical |
| ISO 10350-1:2017 | Identical |
| NBN EN ISO 10350-1 : 2008 AMD 1 2014 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 75-1:2013 | Plastics — Determination of temperature of deflection under load — Part 1: General test method |
| ISO 10350-2:2011 | Plastics — Acquisition and presentation of comparable single-point data — Part 2: Long-fibre-reinforced plastics |
| ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 3915:1981 | Plastics — Measurement of resistivity of conductive plastics |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| ISO 294-3:2002 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates |
| ISO 1133-1:2011 | Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| IEC 62631-3-2:2015 | Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| IEC 62631-3-1:2016 | Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11357-3:2011 | Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature and enthalpy of melting and crystallization |
| ISO 11357-2:2013 | Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and glass transition step height |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| ISO 294-4:2001 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of moulding shrinkage |
| ISO 2577:2007 | Plastics — Thermosetting moulding materials — Determination of shrinkage |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method |
| ISO 291:2008 | Plastics — Standard atmospheres for conditioning and testing |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 62:2008 | Plastics — Determination of water absorption |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 1133-2:2011 | Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 2: Method for materials sensitive to time-temperature history and/or moisture |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 11403-1:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 1: Mechanical properties |
| ISO 20753:2008 | Plastics — Test specimens |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : Users cannot be edited or removed once added to your Multi user PDF.