I.S. EN ISO 12100-2:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
Hardcopy , PDF
15-11-2010
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Inherently safe design measures
4.1 General
4.2 Consideration of geometrical factors and physical
aspects
4.3 Taking into account the general technical knowledge
regarding machine design
4.4 Choice of an appropriate technology
4.5 Applying the principle of the positive mechanical
action of a component on another component
4.6 Provisions for stability
4.7 Provisions for maintainability
4.8 Observing ergonomic principles
4.9 Preventing electrical hazard
4.10 Preventing hazards from pneumatic and hydraulic
equipment
4.11 Applying inherently safe design measures to control
system
4.12 Minimizing the probability of failure of safety
functions
4.13 Limiting exposure to hazards through reliability of
equipment
4.14 Limiting exposure to hazards through mechanization or
automation of loading (feeding)/unloading (removal)
operations
4.15 Limiting exposure to hazards through location of the
setting and maintenance points outside of danger
zones
5 Safeguarding and complementary protective measures
5.1 General
5.2 Selection and implementation of guards and
protective devices
5.3 Requirements for the design of guards and
protective devices
5.4 Safeguarding for reducing emissions
5.5 Complementary protective measures
6 Information for use
6.1 General requirements
6.2 Location and nature of the information for use
6.3 Signals and warning devices
6.4 Markings, signs (pictograms), written warnings
6.5 Accompanying documents (in particular,
instruction handbook)
Bibliography
Annex ZA (informative) - Equivalence between the ISO standards
and the European standards
Annex ZB (informative) - Relationship between this International
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZC (informative) - Relationship between this International
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Gives technical principles to help designers in achieving safety in the design of machinery.
| DevelopmentNote |
Supersedes I.S. EN 292-2 (12/2003)
|
| DocumentType |
Standard
|
| Pages |
110
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| SN EN ISO 12100-2 : 2004 AMD 1 2009 | Identical |
| NS EN ISO 12100-2 : 2003 AMD 1 2009 | Identical |
| NEN EN ISO 12100-2 : 2003 AMD 1 2009 | Identical |
| NBN EN ISO 12100-2 : 2003 AMD 1 2009 | Identical |
| UNE-EN ISO 12100-2:2004 | Identical |
| BS EN ISO 12100-2 : 2003 | Identical |
| NF EN ISO 12100-2 : 2004 AMD 1 2009 | Identical |
| UNI EN ISO 12100-2 : 2009 | Identical |
| ISO 12100-2:2003 | Identical |
| DIN EN ISO 12100-2:2004-04 | Identical |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| ISO 10075-2:1996 | Ergonomic principles related to mental workload — Part 2: Design principles |
| ISO 13855:2010 | Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 14119:2013 | Safety of machinery — Interlocking devices associated with guards — Principles for design and selection |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| ISO 14120:2015 | Safety of machinery Guards General requirements for the design and construction of fixed and movable guards |
| EN 50020:2002 | Electrical apparatus for potentially explosive atmospheres - Intrinsic safety 'i' |
| ISO 15667:2000 | Acoustics Guidelines for noise control by enclosures and cabins |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| EN 13861:2011 | Safety of machinery - Guidance for the application of ergonomics standards in the design of machinery |
| EN 811 : 1996 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| ISO 9355-1:1999 | Ergonomic requirements for the design of displays and control actuators — Part 1: Human interactions with displays and control actuators |
| ISO 13852:1996 | Safety of machinery Safety distances to prevent danger zones being reached by the upper limbs |
| EN 1299:1997+A1:2008 | Mechanical vibration and shock - Vibration isolation of machines - Information for the application of source isolation |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| IEC 61310-3:2007 | Safety of machinery - Indication, marking and actuation - Part 3: Requirements for the location and operation of actuators |
| ISO 14118:2000 | Safety of machinery Prevention of unexpected start-up |
| EN 1760-1:1997+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors |
| ISO 13851:2002 | Safety of machinery Two-hand control devices Functional aspects and design principles |
| ISO 14123-1:2015 | Safety of machinery Reduction of risks to health resulting from hazardous substances emitted by machinery Part 1: Principles and specifications for machinery manufacturers |
| EN 50144-1 : 98 COR 2005 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 1: GENERAL REQUIREMENTS |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| ISO 447:1984 | Machine tools Direction of operation of controls |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| ISO 13853:1998 | Safety of machinery Safety distances to prevent danger zones being reached by the lower limbs |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| IEC 62079:2001 | Preparation of instructions - Structuring, content and presentation |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| IEC 60745-1:2006 | Hand-held motor-operated electric tools - Safety - Part 1: General requirements |
| ISO 14163:1998 | Acoustics — Guidelines for noise control by silencers |
| ISO 2972:1979 | Numerical control of machines — Symbols |
| EN 12198-3:2002+A1:2008 | Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 3: Reduction of radiation by attenuation or screening |
| ISO 13854:2017 | Safety of machinery — Minimum gaps to avoid crushing of parts of the human body |
| ISO 13856-1:2013 | Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| EN 12198-1:2000+A1:2008 | Safety of machinery - Assessment and reduction of risks arising from radiation emitted by machinery - Part 1: General principles |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 626-1:1994+A1:2008 | Safety of machinery - Reduction of risks to health from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| IEC 62061:2005+AMD1:2012+AMD2:2015 CSV | Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems |
| EN 61496-2:2013 | Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| ISO 10075:1991 | Ergonomic principles related to mental work-load General terms and definitions |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| IEC TS 62046:2008 | Safety of machinery - Application of protective equipment to detect the presence of persons |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 6385:2016 | Ergonomics principles in the design of work systems |
| IEC 61496-2:2013 | Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.