• There are no items in your cart

I.S. EN ISO 4042:1999

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

FASTENERS - ELECTROPLATED COATINGS

Available format(s)

Hardcopy , PDF

Superseded date

09-10-2018

Superseded by

I.S. EN ISO 4042:2018

Language(s)

English

Published date

01-01-1999

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.


Dates of withdrawal of national standards are available from NSAI.

€64.00
Excluding VAT

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Dimensional requirements and gauging
      4.1 Dimensional requirements before electroplating
      4.2 Dimensional requirements after electroplating
5 Other coating requirements
6 Hydrogen embrittlement relief
7 Corrosion protection
8 Applicability to fasteners that cut or form their own
      mating threads
9 Specification of coating thickness
10 Measurement of coating thickness
      10.1 Local thickness
      10.2 Batch average thickness
      10.3 Agreement on test method
11 Sampling for thickness tests
12 Ordering requirements for electroplating
13 Designation
Annex A (informative) Hydrogen embrittlement relief
Annex B (informative) Salt spray corrosion protection
                       performance of metallic coatings
Annex C (informative) Guidance on procedures that may be
                       adopted to accommodate thick coatings
Annex D (normative) Determination of batch average thickness
Annex E (normative) Designation code, system A, for
                     electroplated coatings on threaded parts
Annex F (informative) Examples for coating designation
Annex G (informative) Surface areas of bolts, screws and nuts
Annex ZA (normative) Normative references to international
         publications with their relevant European publications
Bibliography

Defines dimensional requirements for electroplated fasteners of steel or copper alloy. Defines thicknesses of coating and provides recommendations for hydrogen embrittlement relief for fasteners having high tensile strength or hardness and for surface-hardened fasteners. Deals mainly with the electroplating of threaded fasteners, but may also be applicable to other threaded parts, and nonthreaded eg. washers and pins.

DocumentType
Standard
Pages
34
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

ISO 8991:1986 Designation system for fasteners
ISO 9587:2007 Metallic and other inorganic coatings Pretreatment of iron or steel to reduce the risk of hydrogen embrittlement
ISO 2082:2017 Metallic and other inorganic coatings — Electroplated coatings of cadmium with supplementary treatments on iron or steel
ISO 965-2:1998 ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality
EN ISO 2064:2000 Metallic and other inorganic coatings - Definitions and conventions concerning the measurement of thickness (ISO 2064:1996)
ISO 1502:1996 ISO general-purpose metric screw threads Gauges and gauging
ISO 15330:1999 Fasteners — Preloading test for the detection of hydrogen embrittlement — Parallel bearing surface method
ISO 1458:2002 Metallic coatings Electrodeposited coatings of nickel
ISO 2081:2008 Metallic and other inorganic coatings Electroplated coatings of zinc with supplementary treatments on iron or steel
ISO 1456:2009 Metallic and other inorganic coatings — Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium
ISO 9588:2007 Metallic and other inorganic coatings Post-coating treatments of iron or steel to reduce the risk of hydrogen embrittlement
ISO 4520:1981 Chromate conversion coatings on electroplated zinc and cadmium coatings
ISO 9227:2017 Corrosion tests in artificial atmospheres — Salt spray tests
ISO 965-1:2013 ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 965-3:1998 ISO general purpose metric screw threads Tolerances Part 3: Deviations for constructional screw threads
ISO 2064:1996 Metallic and other inorganic coatings — Definitions and conventions concerning the measurement of thickness
ISO 3269:2000 Fasteners Acceptance inspection

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.