I.S. EN ISO 5199:2002
Current
The latest, up-to-date edition.
TECHNICAL SPECIFICATIONS FOR CENTRIFUGAL PUMPS - CLASS 2
Hardcopy , PDF
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Dates of withdrawal of national standards are available from NSAI.
Important note : Users cannot be edited or removed once added to your Multi user PDF.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Design
4.1 General
4.2 Prime movers
4.3 Critical speed, balance and vibration
4.4 Pressure-containing parts
4.5 Branches (nozzles) and miscellaneous connections
4.6 External forces and moments on flanges (inlet and
outlet)
4.7 Branch (nozzle) flanges
4.8 Impellers
4.9 Wear rings or equivalent components
4.10 Running clearance
4.11 Shafts and shaft sleeves
4.12 Bearings
4.13 Shaft sealing
4.14 Labelling
4.15 Couplings
4.16 Baseplate
4.17 Special tools
5 Materials
5.1 Selection of materials
5.2 Material composition and quality
5.3 Repairs
6 Shop inspection and tests
6.1 General
6.2 Inspection
6.3 Tests
6.4 Final inspection
7 Preparation for dispatch
7.1 Shaft seals
7.2 Preservation for transport and storage
7.3 Securing of rotating parts for transport
7.4 Openings
7.5 Piping and auxiliaries
7.6 Identification
Annex A (normative) Centrifugal pump - Data sheet
Annex B (informative) External forces and moments on branches
Annex C (normative) Enquiry, proposal, purchase order
Annex D (normative) Documentation after purchase order
Annex E (informative) Examples of seal arrangements
Annex F (informative) Piping arrangements for seals
Annex G (informative) Designation examples using
references from annexes E and F
Annex H (informative) Checklist
Bibliography
Defines the requirements for class 2 centrifugal pumps of single-stage, multistage, horizontal or vertical construction, with any drive and any installation for general application.
| DevelopmentNote |
Supersedes I.S. EN 25199 (01/2003)
|
| DocumentType |
Standard
|
| Pages |
70
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN ISO 5199:2002 | Identical |
| NS EN ISO 5199 : 1ED 2002 | Identical |
| UNI EN ISO 5199 : 2005 | Identical |
| ISO 5199:2002 | Identical |
| NF EN ISO 5199 : 2002 | Identical |
| UNE-EN ISO 5199:2002 | Identical |
| BS EN ISO 5199:2002 | Identical |
| SN EN ISO 5199 : 2003 | Identical |
| NBN EN ISO 5199 : 2002 | Identical |
| NEN EN ISO 5199 : 2002 | Identical |
| DIN EN ISO 5199:2003-12 | Identical |
| ISO 9906:2012 | Rotodynamic pumps — Hydraulic performance acceptance tests — Grades 1, 2 and 3 |
| ISO 3511-1:1977 | Process measurement control functions and instrumentation — Symbolic representation — Part 1: Basic requirements |
| ISO 3511-3:1984 | Process measurement control functions and instrumentation — Symbolic representation — Part 3: Detailed symbols for instrument interconnection diagrams |
| ISO 9905:1994 | Technical specifications for centrifugal pumps — Class I |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 9614-1:1993 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points |
| ISO 9908:1993 | Technical specifications for centrifugal pumps — Class III |
| EN 22858:1993 | End-suction centrifugal pumps (rating 16 bar) - Designation, nominal duty point and dimensions (ISO 2858:1975) |
| ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
| ISO 1940-1:2003 | Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances |
| ISO 9614-2:1996 | Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning |
| ISO 281-1:1977 | Rolling bearings Dynamic load ratings and rating life Part 1: Calculation methods |
| ISO 2041:2009 | Mechanical vibration, shock and condition monitoring Vocabulary |
| EN 23661:1993 | End-suction centrifugal pumps - Baseplate and installation dimensions (ISO 3661:1977) |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| ISO 3511-2:1984 | Process measurement control functions and instrumentation — Symbolic representation — Part 2: Extension of basic requirements |
| ISO 10816-1:1995 | Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 1: General guidelines |
| ISO 3274:1996 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments |
| ISO 2858:1975 | End-suction centrifugal pumps (rating 16 bar) — Designation, nominal duty point and dimensions |
| EN ISO 9614-2:1996 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 2: Measurement by scanning (ISO 9614-2:1996) |
| ISO 1219-1:2012 | Fluid power systems and components — Graphical symbols and circuit diagrams — Part 1: Graphical symbols for conventional use and data-processing applications |
| EN ISO 9906:2012 | Rotodynamic pumps - Hydraulic performance acceptance tests - Grades 1, 2 and 3 (ISO 9906:2012) |
| ISO 3661:1977 | End-suction centrifugal pumps — Baseplate and installation dimensions |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| CR 13931 : 2000 | ROTODYNAMIC PUMPS - FORCES AND MOMENTS ON FLANGES CENTRIFUGAL, MIXED FLOW AND AXIAL FLOW PUMPS HORIZONTAL AND VERTICAL SHAFTS |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| ISO 3069:2000 | End-suction centrifugal pumps — Dimensions of cavities for mechanical seals and for soft packing |
| ISO 76:2006 | Rolling bearings Static load ratings |
| EN ISO 3274:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method - Nominal characteristics of contact (stylus) instruments (ISO 3274:1996) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.