IEC TR 62039:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Selection guide for polymeric materials for outdoor use under HV stress
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
24-08-2021
English
13-03-2007
Important note : Users cannot be edited or removed once added to your Multi user PDF.Presents the important material properties for polymeric materials used in outdoor insulation and, where applicable, lists the standardised test methods including the minimum requirements. If no standardised tests are available, then test methods reported in literature are summarised. This report is valid for insulating materials used in outdoor high voltage electrical applications with a system voltage greater than 1000 V a.c. having polymeric insulation including also such applications where the housing is an integral part of the devices e.g. in surge arrestors and cable terminations. The scope of this report is limited to the materials only. The performance of insulators in service depends on several factors such as the type of material, the design, environmental conditions etc. Consequently, the choice of materials that fulfil the requirements listed below is a necessary condition but does not guarantee satisfactory performance when used in outdoor insulation
| Committee |
TC 112
|
| DevelopmentNote |
Stability Date: 2017. (11/2012)
|
| DocumentType |
Technical Report
|
| Pages |
14
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| SAC GB/Z 28818 : 2012 | Identical |
| PD IEC/TR 62039:2007 | Identical |
| NEN NPR IEC/TR 62039 : 2007 | Identical |
| NBR IEC/TR 62039 : 2010 | Identical |
| CEI EN 61462 : 2008 | COMPOSITE HOLLOW INSULATORS - PRESSURIZED AND UNPRESSURIZED INSULATORS FOR USE IN ELECTRICAL EQUIPMENT WITH RATED VOLTAGE GREATER THAN 1000 V - DEFINITIONS, TEST METHODS, ACCEPTANCE CRITERIA AND DESIGN RECOMMENDATIONS |
| CEI 36-43 : 2011 | SELECTION AND DIMENSIONING OF HIGH-VOLTAGE INSULATORS INTENDED FOR USE IN POLLUTED CONDITIONS - PART 3: POLYMER INSULATORS FOR A.C. SYSTEMS |
| DD IEC/TS 60815-1:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions Definitions, information and general principles |
| I.S. EN 61462:2007 | COMPOSITE HOLLOW INSULATORS - PRESSURIZED AND UNPRESSURIZED INSULATORS FOR USE IN ELECTRICAL EQUIPMENT WITH RATED VOLTAGE GREATER THAN 1 000 V - DEFINITIONS, TEST METHODS, ACCEPTANCE CRITERIA AND DESIGN RECOMMENDATIONS |
| CEI 36-41 : 2011 | SELECTION AND DIMENSIONING OF HIGH-VOLTAGE INSULATORS INTENDED FOR USE IN POLLUTED CONDITIONS - PART 1: DEFINITIONS, INFORMATION AND GENERAL PRINCIPLES |
| EN 60505:2011/AC:2017-03 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS (IEC 60505:2011/COR1:2017) |
| BS EN 61462:2007 | Composite hollow insulators. Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1000 V. Definitions, test methods, acceptance criteria and design recommendations |
| CLC/TR 62662:2011 | Guidance for production, testing and diagnostics of polymer insulators with respect to brittle fracture of core materials |
| I.S. EN 60505:2011 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS |
| IEC TS 60815-3:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems |
| PD CLC/TR 62662:2011 | Measurement procedures for materials used in photovoltaic modules Encapsulants. Test procedure of optical durability |
| IEC TS 60815-1:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles |
| BS PD IEC/TR 62662 : 2010 | GUIDANCE FOR PRODUCTION, TESTING AND DIAGNOSTICS OF POLYMER INSULATORS WITH RESPECT TO BRITTLE FRACTURE OF CORE MATERIALS |
| BS EN 60505:2011 | Evaluation and qualification of electrical insulation systems |
| DD IEC/TS 60815-3:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions Polymer insulators for a.c. systems |
| CEI CLC/TR 62662 : 2012 | GUIDANCE FOR PRODUCTION, TESTING AND DIAGNOSTICS OF POLYMER INSULATORS WITH RESPECT TO BRITTLE FRACTURE OF CORE MATERIALS |
| CEI EN 60505 : 2012 | EVALUATION AND QUALIFICATION OF ELECTRICAL INSULATION SYSTEMS |
| IEC TR 62662:2010 | Guidance for production, testing and diagnostics of polymer insulators with respect to brittle fracture of core materials |
| IEC 60505:2011 | Evaluation and qualification of electrical insulation systems |
| EN 61462:2007 | Composite hollow insulators - Pressurized and unpressurized insulators for use in electrical equipment with rated voltage greater than 1 000 V - Definitions, test methods, acceptance criteria and design recommendations |
| S.R. CLC/TR 62662:2011 | GUIDANCE FOR PRODUCTION, TESTING AND DIAGNOSTICS OF POLYMER INSULATORS WITH RESPECT TO BRITTLE FRACTURE OF CORE MATERIALS (IEC/TR 62662:2010) |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| IEC 60455-2:2015 | Resin based reactive compounds used for electrical insulation - Part 2: Methods of test |
| IEC 62217:2012 | Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria |
| IEC 61621:1997 | Dry, solid insulating materials - Resistance test to high-voltage, low-current arc discharges |
| IEC 61109:2008 | Insulators for overhead lines - Composite suspension and tension insulators for a.c. systems with a nominal voltage greater than 1 000 V - Definitions, test methods and acceptance criteria |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| ISO 34-1:2015 | Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces |
| ISO 11357-2:2013 | Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 4892-3:2016 | Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 4892-4:2013 | Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| IEC 60587:2007 | Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion |
| IEC 61006:2004 | Electrical insulating materials - Methods of test for the determination of the glass transition temperature |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.