ISA 84.00.01-2 : 2004

UNITED STATES NATIONAL FOREWORD
IEC FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions and abbreviations
4 Conformance to this International Standard
5 Management of functional safety
   5.1 Objective
   5.2 Requirements
6 Safety lifecycle requirements
   6.1 Objectives
   6.2 Requirements
7 Verification
   7.1 Objective
8 Process hazard and risk assessment
   8.1 Objectives
   8.2 Requirements
9 Allocation of safety functions to protection layers
   9.1 Objective
   9.2 Requirements of the allocation process
   9.3 Additional requirements for safety integrity level
        4
   9.4 Requirement on the basic process control system as
        a layer of protection
   9.5 Requirements for preventing common cause, common
        mode and dependent failures
10 SIS safety requirements specification
   10.1 Objective
   10.2 General requirements
   10.3 SIS safety requirements
11 SIS design and engineering
   11.1 Objective
   11.2 General requirements
   11.3 Requirements for system behaviour on detection of
        a fault
   11.4 Requirements for hardware fault tolerance
   11.5 Requirements for selection of components and
        subsystems
   11.6 Field devices
   11.7 Interfaces
   11.8 Maintenance or testing design requirements
   11.9 SIF probability of failure
12 Requirements for application software, including selection
   criteria for utility software
   12.1 Application software safety lifecycle requirements
   12.2 Application software safety requirements specification
   12.3 Application software safety validation planning
   12.4 Application software design and development
   12.5 Integration of the application software with the SIS
        subsystem
   12.6 FPL and LVL software modification procedures
   12.7 Application software verification
13 Factory acceptance testing (FAT)
   13.1 Objectives
   13.2 Recommendations
14 SIS installation and commissioning
   14.1 Objectives
   14.2 Requirements
15 SIS safety validation
   15.1 Objective
   15.2 Requirements
16 SIS operation and maintenance
   16.1 Objectives
   16.2 Requirements
   16.3 Proof testing and inspection
17 SIS modification
   17.1 Objective
   17.2 Requirements
18 SIS decommissioning
   18.1 Objectives
   18.2 Requirements
19 Information and documentation requirements
   19.1 Objectives
   19.2 Requirements
Annex A (informative) Example of techniques for calculating
        the probability of failure on demand for a safety
        instrumented function
   A.1 General
   A.2 Reliability block diagram technique
   A.3 Simplified equations technique
   A.4 Fault tree analysis technique
   A.5 Markov modelling technique
Annex B (informative) Typical SIS architecture development
   B.1 Background
   B.2 Work process
   B.3 Example 1
   B.4 Example 2
Annex C (informative) Application features of a safety PLC
   C.1 System
   C.2 Work process
Annex D (informative) Example of SIS logic application
        software development methodology
   D.1 Summary of the overall system integration process
   D.2 SIS logic solver application development software
   D.3 Coding standards for the application programmer
   D.4 Other requirements for configuration/programming
        and run-time systems for safety applications
   D.5 Assumptions
Annex E (informative) Example of development of externally
        configured diagnostics for a safety-configured PE
        logic solver
   E.1 Internally configured diagnostics
   E.2 Externally configured diagnostics
   E.3 Reference

Provides guidance on the specification, design, installation, operation and maintenance of Safety Instrumented Functions and related safety instrumented system as defined in ANSI/ISA-84.00.01-2004 Part 1.