S.R. CLC/TS 60034-25:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
Hardcopy , PDF
08-02-2024
English
01-01-2008
Important note : Users cannot be edited or removed once added to your Multi user PDF.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 System characteristics
5 Losses and their effects (for induction motors fed from
U-converters)
6 Noise, vibration and torsional oscillation
7 Motor insulation electrical stresses
8 Bearing currents
9 Installation
10 Additional considerations for permanent magnet (PM)
synchronous motors fed by U-converters
11 Additional considerations for cage induction motors
fed by high voltage U-converters
12 Additional considerations for synchronous motors
fed U-converters
13 Additional considerations for cage induction motors
fed by block-type I-converters
14 Additional considerations for synchronous motors
fed by LCI
15 Additional considerations for pulsed I-converters (PWM CSI)
feeding induction motors
16 Other motor/converter systems
Annex A (normative) - Converter characteristics
Annex B (informative) - Converter output spectra
Annex C (informative) - Noise increments due to converter
supply
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding
European publications
Defines the design features and performance characteristics of a.c. motors specifically designed for use on converter supplies.
| DevelopmentNote |
Supersedes I.S. CLC TS 60034-25. (10/2009) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
77
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| CLC/TS 60034-25:2008 | Identical |
| IEC 61800-3:2017 | Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods |
| IEC 61800-2:2015 | Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems |
| IEC 61800-4:2002 | Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV |
| EN 61800-5-2:2017 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| IEC 60034-9:2003+AMD1:2007 CSV | Rotating electrical machines - Part 9: Noise limits |
| IEC 60050-195:1998 | International Electrotechnical Vocabulary (IEV) - Part 195: Earthing and protection against electric shock |
| EN 60034-1:2010/corrigendum Oct. 2010 | ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE |
| IEC TR 61000-5-2:1997 | Electromagnetic compatibility (EMC) - Part 5: Installation and mitigation guidelines - Section 2: Earthing and cabling |
| EN 60034-14:2004/A1:2007 | ROTATING ELECTRICAL MACHINES - PART 14: MECHANICAL VIBRATION OF CERTAIN MACHINES WITH SHAFT HEIGHTS 56 MM AND HIGHER - MEASUREMENT, EVALUATION AND LIMITS OF VIBRATION SEVERITY |
| IEC TS 60034-18-41:2006 | Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters |
| EN 60034-9:2005/A1:2007 | ROTATING ELECTRICAL MACHINES - PART 9: NOISE LIMITS |
| EN 61800-5-1:2007/A1:2017 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007/A1:2016) |
| EN 61800-2:2015 | Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems |
| IEC TS 60034-17:2006 | Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide |
| IEC 60034-14:2003+AMD1:2007 CSV | Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| IEC 60034-2:1972 | Rotating electrical machines. Part 2: Methods for determining losses and efficiency of rotating electrical machinery from tests (excluding machines for traction vehicles) |
| EN 61800-3 : 2004 AMD 1 2012 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004/A1:2011) |
| EN 60034-2:1996/A2:1996 | ROTATING ELECTRICAL MACHINES - PART 2: METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF ROTATING ELECTRICAL MACHINERY FROM TESTS (EXCLUDING MACHINES FOR TRACTION VEHICLES) |
| IEC TR 61800-6:2003 | Adjustable speed electrical power drive systems - Part 6: Guide for determination of types of load duty and corresponding current ratings |
| EN 60034-6:1993 | Rotating electrical machines - Part 6: Methods of cooling (IC Code) |
| IEC 61800-5-2:2016 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| IEC TR 61000-5-1:1996 | Electromagnetic compatibility (EMC) - Part 5: Installation and mitigation guidelines - Section 1: General considerations - Basic EMC publication |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.