SAE J429_201405
Current
Current
The latest, up-to-date edition.
Mechanical and Material Requirements for Externally Threaded Fasteners
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
07-05-2014
Publisher
Important note : Users cannot be edited or removed once added to your Multi user PDF.
1. SCOPE
2. REFERENCES
3. DESIGNATIONS
4. MATERIALS AND PROCESSES
5. MECHANICAL REQUIREMENTS
6. METHODS OF TEST
7. PRODUCT MARKING - BOLTS AND SCREWS
8. TEST REQUIREMENTS
9. NOTES
APPENDIX A
Specifies the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems, and U-bolts in sizes to 1-1/2 in. inclusive.
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
SAE International
|
| Status |
Current
|
| Supersedes |
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems2x, and U-bolts2x in sizes to 1-1/2 in. inclusive.The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts.The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing. Other properties such as fatigue behavior, corrosion resistance, impact properties, etc., are beyond the scope of this document and responsibility for ensuring the acceptability of the product for applications where conditions warrant consideration of these other properties shall be borne by the end user.
| A-A-59438 Revision A:2013 | Playpipe: Nozzle, Fire Hose |
| 10/30199074 DC : 0 | BS ISO 6162-1 - HYDRAULIC FLUID POWER - FLANGE CONNECTORS WITH SPLIT OR ONE-PIECE FLANGE CLAMPS AND METRIC OR INCH SCREWS - PART 1: FLANGE CONNECTORS FOR USE AT PRESSURES OF 3,5 MPA (35 BAR) TO 35 MPA (350 BAR), DN 13 TO DN 127 |
| SAE J2295_201611 | Fastener Part Standard - Cap Screws, Hex, Heavy Hex and Heavy Hex Structural Bolts, and Hex Nuts (Inch Dimensioned) |
| SAE J1040_200305 | Performance Criteria for Rollover Protective Structures (ROPS) for Construction, Earthmoving, Forestry, and Mining Machines |
| MIL-DTL-24696 Revision C:2008 | GASKET, SHEET, NON-ASBESTOS |
| MIL-A-52940 Revision C:1987 | AEROSOL GENERATOR, NON-THERMAL, INSECTICIDE, ULTRA LOW VOLUME |
| MIL-C-555 Revision L:1991 | COMPRESSOR, AIR RECIPROCATING AND ROTARY, DIESEL ENGINE DRIVEN |
| A-A-52512 Base Document:1995 | WINCH, DRUM POWER OPERATED, 1-TON PULL, PNEUMATIC |
| MIL-DTL-45912 Revision B:2013 | BOLT, SELF-LOCKING, HEXAGON HEAD, STEEL |
| SAE AS 4775 : 2017 | AIRCRAFT MAINTENANCE JACKS - GENERAL REQUIREMENTS |
| SAE J58_201502 | Flanged 12-Point Screws |
| SAE J2194_201611 | Roll-Over Protective Structures (ROPS) for Wheeled Agricultural Tractors |
| BS EN ISO 10442:2002 | Petroleum, chemical and gas service industries. Packaged, integrally geared centrifugal air compressors |
| MIL-A-52767 Revision D:1989 | AIR CONDITIONER: VERTICAL AND HORIZONTAL, COMPACT |
| MIL-P-52327 Revision C:1990 | PUMPS, CENTRIFUGAL, ELECTRIC-MOTOR-DRIVEN, POSITIVE PRIME, PETROLEUM PRODUCTS, AIRFIELD DEFUELLING AND RECEIVING |
| MIL-DTL-1222 Revision J:2000 | STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR |
| SAE J518/1_202303 | Hydraulic Flange Tube, Pipe, and Hose Connections Four-Screw Flange Connection - Part 1: 3.5 to 35 MPa (Code 61) |
| ASME B18.5 : 2012 : R2017 | ROUND HEAD BOLTS (INCH SERIES) |
| MIL-S-63540 Revision C:1995 | STUD, SELF-CLINCHING GENERAL SPECIFICATION FOR |
| FF-S-85 Revision D:2005 | Screw, Cap, Slotted and Hexagon Head |
| MIL-DTL-45913 Revision D:2011 | NUTS, SELF-LOCKING, HEXAGON, PREVAILING TORQUE |
| ASME B18.5 : 2012 | ROUND HEAD BOLTS (INCH SERIES) |
| MIL-B-45908 Revision B:1985 | BOLT, EYE, GENERAL SPECIFICATION FOR |
| GG-T-35 Revision C:1989 | TABLE; DRAWING, TRACING, AND SCRIBING |
| MIL-H-4607 Revision E:1987 | HEATER, ENGINE AND SHELTER, GROUND |
| MIL B 45912 : A | BOLT, SELF-LOCKING, HEXAGON HEAD, STEEL |
| DIN EN 15001-1:2011-02 | Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| MIL C 00555 : K | COMPRESSORS, AIR, RECIPROCATING AND ROTARY, DIESEL ENGINE DRIVEN |
| 11/30232899 DC : 0 | BS ISO 6162-2 - HYDRAULIC FLUID POWER - FLANGE CONNECTIONS WITH SPLIT OR ONE-PIECE FLANGE CLAMPS AND METRIC OR INCH SCREWS - PART 2: FLANGE CONNECTORS, PORTS AND MOUNTING SURFACES FOR USE AT A PRESSURE OF 42 MPA (420 BAR), DN 13 TO DN 76 |
| MIL S 1222 : H | STUD, BOLTS, HEX CAP SCREWS, SOCKET HEAD CAP SCREWS AND NUTS |
| MIL-P-10360 Revision G:1993 | PUMP, CENTRIFUGAL 4 INCH AND 6 INCH, GASOLINE ENGINE AND DIESEL ENGINE DRIVEN FOR WATER |
| MIL-P-52746 Revision C:1994 | PUMP ASSEMBLY, FLAMMABLE LIQUID, CENTRIFUGAL, SELF PRIMING 2 INCH 100 GPM AT 100 FEET TOTAL DYNAMIC HEAD |
| ASTM D 5657 : 2007 | Standard Test Method for Fluid Tightness Ability of Adhesives Used on Threaded Fasteners |
| ASTM F 2437/F2437M : 2017 : REDLINE | Standard Specification for Carbon and Alloy Steel Compressible-Washer-Type Direct Tension Indicators for Use with Cap Screws, Bolts, Anchors, and Studs |
| AGMA 6001 : REV D : 1997 | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| IFI 124 : 2002 | TEST PROCEDURE FOR THE PERFORMANCE OF NONMETALLIC RESISTANT ELEMENT PREVAILING-TORQUE SCREWS |
| IFI 160 : 2007 | TEST PROCEDURE FOR THE PERFORMANCE OF NUTS WITH PRE-APPLIED ADHESIVE COATED THREADS - INCH SERIES |
| SAE J518/3_201511 | Hydraulic Flange Clamps, 2-Screw Flange Connection to be used with SAE J518-1 (Code 61) Connections where Only Low Pressure is Required |
| ASTM F 1510 : 2007 : R2013 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
| ASTM D 5648 : 2001 : R2008 | Standard Test Method for Torque-Tension Relationship of Adhesives Used on Threaded Fasteners (Lubricity) |
| ASTM D 5648 : 2001 : R2014 | Standard Test Method for Torque-Tension Relationship of Adhesives Used on Threaded Fasteners (Lubricity) |
| AWWA C541 : 2016 | HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES |
| I.S. EN ISO 10441:2007 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FLEXIBLE COUPLINGS FOR MECHANICAL POWER TRANSMISSION - SPECIAL-PURPOSE APPLICATIONS |
| API 671 : 2007 | SPECIAL PURPOSE COUPLINGS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES |
| C83-17 | COMMUNICATION AND POWER LINE HARDWARE |
| SAE J1102_201611 | Mechanical and Material Requirements for Wheel Bolts |
| SAE J518_201303 | Hydraulic Flanged Tube, Pipe, and Hose Connections, Four-Bolt Split Flange Type |
| FF-C-450 Revision G:2017 | CLAMPS, WIRE ROPE |
| ANSI/HI 9.6.2 : 2015 | ROTODYNAMIC PUMPS FOR ASSESSMENT OF APPLIED NOZZLE LOADS |
| MIL V 12126 : E | VALVE, GATE, BRONZE, LEVER OPERATED, QUICK OPENING, 125 PSI AND 150 PSI |
| MS51868 Revision E:2017 | CLAMP, WIRE ROPE, DOUBLE SADDLED, DOUBLE-GRIP, STEEL, TYPE 3 |
| MIL-D-63303 Revision B:1988 | DISPENSER, MINE, GROUND VEHICLE, M128 |
| ISO 6162-2:2018 | Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76 |
| SAE J518/2_201704 | Hydraulic Flanged Tube, Pipe, and Hose Connections, 4-Screw Flange Connection Part 2: 42 MPa (Code 62) |
| SAE J1194_201611 | Rollover Protective Structures (ROPS) for Wheeled Agricultural Tractors |
| I.S. EN 13611:2015 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| UNI EN 1106 : 2010 | MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES |
| UNI EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| UNI EN 1854 : 2010 | PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES |
| API 671 : 2007 : R2010 | SPECIAL PURPOSE COUPLINGS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES |
| ASTM F 1510 : 2007 | Standard Specification for Rotary Positive Displacement Pumps, Ships Use |
| MIL-P-52405 Revision C:1990 | PUMPS, CENTRIFUGAL, ELECTRIC-MOTOR-DRIVEN (FOR WATER) |
| BS ISO 6162-1:2012 | Hydraulic fluid power. Flange connections with split or one-piece flange clamps and metric or inch screws Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 |
| SAE J518/1_201301 | Hydraulic Flanged Tube, Pipe, and Hose Connections, 4-Screw Flange Connection Part 1: 3.5 MPa to 35 MPa (Code 61) |
| CSA G401 : 2014 | CORRUGATED STEEL PIPE PRODUCTS |
| CSA B242 : 2005 | GROOVE- AND SHOULDER-TYPE MECHANICAL PIPE COUPLINGS |
| AGMA 6001 : REV D : 1997 : R2003 | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| I.S. EN 15001-1:2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| ASCE 16 95 : 1996 | STANDARD FOR LOAD AND RESISTANCE FACTOR DESIGN (LRFD) FOR ENGINEERED WOOD CONSTRUCTION |
| 17/30360051 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| UNE-EN 13611:2016 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| MSS SP 127 : 2014 | BRACING FOR PIPING SYSTEMS: SEISMIC - WIND - DYNAMIC DESIGN, SELECTION, AND APPLICATION |
| SAE J2486_201304 | Tension Indicating Washer Tightening Method for Fasteners |
| CSA S16 : 2014 | DESIGN OF STEEL STRUCTURES |
| ISO 6162-1:2012 | Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 |
| BS EN ISO 10441:2007 | Petroleum, petrochemical and natural gas industries. Flexible couplings for mechanical power transmission. Special-purpose applications |
| UNE-EN 15001-1:2010 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| CSA O86 : 2014 | ENGINEERING DESIGN IN WOOD |
| ISO 10442:2002 | Petroleum, chemical and gas service industries Packaged, integrally geared centrifugal air compressors |
| ISO 10441:2007 | Petroleum, petrochemical and natural gas industries Flexible couplings for mechanical power transmission Special-purpose applications |
| EN 15001-1:2009 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| EN ISO 10441:2007 | Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007) |
| EN ISO 10442:2002 | Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002) |
| SAE J1199_201302 | Mechanical and Material Requirements for Metric Externally Threaded Steel Fasteners |
| ASTM D 5648 : 2001 : R2019 | Standard Test Method for Torque-Tension Relationship of Adhesives Used on Threaded Fasteners (Lubricity) |
| ASTM D 5657 : 2007 : R2014 | Standard Test Method for Fluid Tightness Ability of Adhesives Used on Threaded Fasteners |
| MIL-S-12511 Revision G:1983 | SPRAYER, INSECTICIDE, FRAME MOUNTED, GASOLINE ENGINE DRIVEN, MIST AND SOLID STREAM, 180 GPH |
| 12/30257022 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS |
| MIL N 45913 : B | NUTS, SELF LOCKING, HEXAGON, PREVAILING-TORQUE |
| IFI 136 : 2006 | STUDS AND BENT BOLTS |
| 16/30328245 DC : 0 | BS ISO 6164 - HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 10 TO 80 |
| SAE J1965_201710 | Road Vehicles - Wheels for Commercial Vehicles and Multipurpose Passenger Vehicles - Fixing Nuts - Test Methods |
| MIL-STD-2193 Revision C:2012 | Ship Hydraulic System Components |
| BS EN 15001-1:2009 | Gas infrastructure. Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations Detailed functional requirements for design, materials, construction, inspection and testing |
| ANSI/AWWA D103 : 2009 | FACTORY-COATED BOLTED CARBON STEEL TANKS FOR WATER STORAGE |
| DIN ISO 6162-1:2006-02 | HYDRAULIC FLUID POWER - FLANGE CONNECTORS WITH SPLIT OR ONE-PIECE FLANGE CLAMPS AND METRIC OR INCH SCREWS - PART 1: FLANGE CONNECTORS FOR USE AT PRESSURES OF 3,5 MPA (35 BAR) TO 35 MPA (350 BAR), DN 13 TO DN 127 |
| MIL-C-11071 Revision D:1983 | CLEANING MACHINE, FUEL CAN, DRUM |
| AGMA 6001 : D | DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES |
| CSA B352.0 : 2016 | ROLL-OVER PROTECTIVE STRUCTURES (ROPS), FALLING OBJECT PROTECTIVE STRUCTURES (FOPS), OPERATOR PROTECTIVE STRUCTURES (OPS), AND TIP-OVER PROTECTIVE STRUCTURES (TOPS) FOR MOBILE MACHINERY - GENERAL CANADIAN REQUIREMENTS |
| N287.2-17 | Material requirements for concrete containment structures for nuclear power plants |
| CSA B242 : 2005 : R2016 | GROOVE- AND SHOULDER-TYPE MECHANICAL PIPE COUPLINGS |
| SAE J238_201705 | Nut and Conical Spring Washer Assemblies |
| ASTM D 5363 : 2016 : REDLINE | Standard Specification for Anaerobic Single-Component Adhesives (AN) |
| IFI 124 : 2002 : R2013 | TEST PROCEDURE FOR THE PERFORMANCE OF NONMETALLIC RESISTANT ELEMENT PREVAILING-TORQUE SCREWS |
| DIN ISO 6162-2:2006-02 | HYDRAULIC FLUID POWER - FLANGE CONNECTORS WITH SPLIT OR ONE-PIECE FLANGE CLAMPS AND METRIC OR INCH SCREWS - PART 2: FLANGE CONNECTORS FOR USE AT PRESSURES OF 35 MPA (350 BAR) TO 40 MPA (400 BAR), DN 13 TO DN 51 |
| SAE J935_200911 | High-Strength Carbon and Alloy Die Drawn Steels |
| BS EN 13611:2015 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. General requirements |
| PREN 13611 : DRAFT 2017 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| ASTM D 5648 : 2001 | Standard Test Method for Torque-Tension Relationship of Adhesives Used on Threaded Fasteners (Lubricity) |
| I.S. EN 13611:2015/AC:2016 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| ASME B18.6.2 : 1998 | SLOTTED HEAD CAP SCREWS, SQAURE HEAD SET SCREWS, AND SLOTTED HEADLESS SET SCREWS (INCH SERIES) |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| ASME B18.9 : 2012 : R2017 | PLOW BOLTS |
| ASME B18.31.5 : 2011 | BENT BOLTS (INCH SERIES) |
| SAE J518/2_202312 | Hydraulic Flanged Tube, Pipe, and Hose Connections, Four-Screw Flange Connection - Part 2: 42 MPa (Code 62) |
| API RP 697:2023 | Pump Repair |
| ASME B18.31.5 : 2011 : R2016 | BENT BOLTS (INCH SERIES) |
| ASME B18.31.2 : 2014 | CONTINUOUS THREAD STUD, DOUBLE-END STUD, AND FLANGE BOLTING STUD (STUD BOLT) (INCH SERIES) |
| ASME B18.9 : 2012 | PLOW BOLTS |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| SAE J403_201406 | Chemical Compositions of SAE Carbon Steels |
| SAE J409_199502 | PRODUCT ANALYSIS—PERMISSIBLE VARIATIONS FROM SPECIFIED CHEMICAL ANALYSIS OF A HEAT OR CAST OF STEEL |
| SAE J411_201501 | Carbon and Alloy Steels |
| SAE J1268_201005 | Hardenability Bands for Carbon and Alloy H Steels |
| SAE J417_198312 | HARDNESS TESTS AND HARDNESS NUMBER CONVERSIONS |
| ASTM F 2328 : 2017 : REDLINE | Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts |
| SAE J404_200901 | Chemical Compositions of SAE Alloy Steels |
| ASME B18.18 : 2017 | QUALITY ASSURANCE FOR FASTENERS |
| SAE J995_201202 | Mechanical and Material Requirements for Steel Nuts |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.